Description Of The Unit; Sizes Available; Main Features Of The Ved_I Fan Coils; Accessories - AERMEC VED I Série Manuel Technique

DESCRIPTION OF THE UNIT

FAN COILS WITH INVERTER MOTORISED FAN
− The fan coil is a terminal used to treat air, both during winter and summer. The VED_I fan coils have been designed to meet any requirement
in ducted systems.
− In particular, the fact that the unit can be integrated in the VMF system allows you to control the individual fan coil with accessories up to the
management of the VED_I inserted in complex networks of fan coils and relative accessories.

SIZES AVAILABLE

The VED_I fan coils are available for:
2-pipe systems
VED 530 I EU-EUTH-EUTL EUW
VED 540 I EU-EUTH-EUTL EUW
VED 730 I EU-EUTH-EUTL EUW
VED 740 I EU-EUTH-EUTL EUW

MAIN FEATURES OF THE VED_I FAN COILS

• Fan coil for vertical wall mounted installa-
tion and horizontal suspended ceiling instal-
lation
• Versions for 2-pipe systems with main,
standard or larger coil.
• Versions for 4-pipe systems with also heat-
ing, standard or larger coil.
• Coil with low pressure drops.
• Reversible connections on site.
• Wide range of accessories to connect the

ACCESSORIES

VCF4_C_24V
Kit made up from motorised 3-way valves with
isolating shell, fittings and isolated copper pipes.
For main coils.
24V power supply.
VCF4_H_24V
Kit made up from motorised 3-way valves, fittings
and isolated copper pipes. For heating only coils.
24V power supply.
VCF2_C_24V
Kit made up from motorised 2-way valves, with fit-
tings and isolated copper pipes. For main coils.
24V power supply.
VCF2_H_24V
Kit made up from motorised 2-way valves, with
fittings
and copper pipes. For heating only coils.
24V power supply.
Control panels
Available in 24V and 120V power supply
(contact Aermec office for compatibility).
BV
Single row hot water heat exchanger.
RPA_VUS
is an intake plenum with rectangular flange made of
galvanised sheet steel. This accessory is for connec-
IVEDITI 2102 - 4880986_00
6
Standard coil
Larger coil
Standard coil
Larger coil
fan coil to the air ducting.
• It requires an external control device
(accessory).
• Wide range of controls and accessories.
• Wide possibility to have different useful
static pressure.
• Motorised fan with brushless motor and
dedicated inverter.
• Centrifugal fans with blades designed for
low sound emissions
tion of a channel with a rectangular section to the
intake vent of the unit.
According to requirements, the RPA_VUS accessory
allows for intake both longitudinal and perpendicu-
lar to the air flow passing through the unit. The
sides of the RPA_V intake plenum are set for the
connection of a circular section channel by means of
the KFVUF accessory.
PA_VUS
is an intake plenum made of galvanised sheet steel
with plastic circular flanges having variable section.
This accessory is for connection of channels with
circular section to the intake vent of the unit. Ac-
cording to requirements, the PA_VUS accessory al-
lows for intake both longitudinal and perpendicular
to the air flow passing through the unit.
The sides of the PA_VUS intake plenum are set for
the connection of an additional circular section
channel by means of the KFVUS accessory.
RPM_V:
is a flow plenum with rectangular flange made
of galvanised sheet steel and fully insulated. This
accessory is for connection of a channel with a
rectangular section to the flow vent of the unit.
According to requirements, the RPM_V accessory
allows for both longitudinal and perpendicular
4-pipe systems
VED 532 I EU-EUTH-EUTL EUW Standard battery + increased heating
VED 541 I EU-EUTH-EUTL EUW Larger coil + standard heating
VED 732 I EU-EUTH-EUTL EUW Standard coils + increased heating
VED 741 I EU-EUTH-EUTL EUW Larger coil + standard heating
• Filter with G3 filtration class.
• Intake air filter, easy to remove for periodi-
cal cleaning.
variable water flow rate
• Internal insulation class 1.
• Full compliance with accident-prevention
standards.
• Easy installation and maintenance
• Flow flange obtained directly on the unit.
delivery to the air flow passing through the unit.
The sides of the RPM_V flow plenum are set for the
connection of a circular section channel by means of
the KFV accessory.
PM_V
is a flow plenum made of galvanised sheet steel,
fully insulated with plastic circular flanges having
variable section. This accessory is for connection of
channels with circular section to the flow vent of
the unit. According to requirements, the PM_VUS
accessory allows for both longitudinal and perpen-
dicular delivery to the air flow passing through the
unit. The sides of the PM_VUS flow plenum are set
for the connection of an additional circular section
channel by means of the KFVUS accessory.
RDAC_V
is a straight suction galvanized sheet with circular
flanges variable section plastic. This accessory al-
lows to connect several circular section channel unit
blowing mouth.
KFV
is an intake/flow circular flange kit with variable
section, in plastic. This accessory is for connection
of an additional circular duct, making use of the set-
ups present on the sides of the intake/flow plenum
of the unit.