Emergency Procedure - Güde 335/10/50 Traduction Du Mode D'emploi D'origine

ENGLISH
24
comply with the safety precautions to be adopted
for each type of application (in ation, airpowered
tools, painting, washing with water-based deter-
gents only, clinching, etc.).
When using compressed air, you must know and
comply with the safety precautions to be adopted
for each type of application (in ation, airpowered
tools, painting, washing with water-based deter-
gents only, clinching, etc.).
Caution! Never switch the compressor on or o using
the plug. Pressure switch to be pressed at all times.
Do not leave the compressor on over night as it could
become a source of danger.
At the end of your working day, switch the appliance
o , release the air jet and unplug the compressor.
Warning: if the water that condenses is not drained,
it may corrode the receiver, reducing its capacity and
impairing safety.
Never leave the appliance exposed to adverse wea-
ther conditions (rain, sun, fog, snow).
If this compressor is used outdoors, always remem-
ber to stow it after use in a covered or closed place.
Never use the compressor outdoors in rain or bad
weather.
Do not place ammable or nylon/fabric objects close
to and/or on the compressor.
Do not cover the air inlets on the compressor.
The compressor must not be tted in a vehicle for
industrial purposes without an inspection by an
expert!
If the compressor is used for industrial purposes, it
must be checked by an expert before putting into
operation for the rst time. Such check must be orde-
red by the operator (under BetrSichV Section 17 No.
25 – operation safety regulation)
Caution! When tted in automatic equipment, it is
necessary to install appropriate alarm or warning
devices in case of power outage or malfunction or
compressor (e.g. feed line, etc.) failure.
Requirements for operating sta
To guarantee perfect and reliable operation of
the rotary and percussive pneumatic tools such as
impact wrenches, staplers or nailers, etc., the com-
pressed air must be supplied ltered - with oil via the
lubricator or maintenance unit
A ltered water separator should be used for var-
nishing in any case.
To select a suitable pneumatic tool, the tool air
consumption and the compressor e ective amount
delivered must necessarily be considered.
(Pneumatic tools and accessory equipment can be
found at www.guede.com)
Operation at lower temperatures
At lower temperatures, below 5°C, problems may
be experienced when starting. They are manifested
by growling of the electric motor. In such a case, the
appliance must be immediately switched o and oil
(5W30) changed in warmer conditions.
Requirements for operating sta
The operating sta must carefully read the Opera-
ting Instructions before using the appliance.
Quali cation: Apart from the detailed instructions
by a professional, no special quali cation is necessa-
ry for appliance using.
Minimum age: Persons over 16 years of age can
only work on the appliance. An exception includes
youngsters trained in order to reach knowledge
under supervision of the trainer during occupational
education.
Training: Using the appliance only requires corre-
sponding training by a professional or the Operating
Instructions. No special training is necessary.

Emergency procedure

Conduct a rst-aid procedure adequate to the injury
and summon quali ed medical attendance as quickly
as possible. Protect the injured person from further
harm and calm them down. For the sake of eventual
accident, in accordance with DIN 13164, a workplace
has to be tted with a rst-aid kit. It is essential to
replace any used material in the rst-aid kit immedia-
tely after it has been used.
If you seek help, state the following pieces of infor-
mation:
1. Accident site
2. Accident type
3. Number of injured persons
4. Injury type(s)
Maintenance
Before carrying out any work on the machine,
disconnect the plug from the socket.
Run the accessory connected dry until there is no
more air in the receiver.