Connecting The Antenna; Function Modes - Cardin Elettronica GL Série Mode D'emploi

REMOTE CONTROL (fig. 7, 8 - pages 8, 9)
The system can be remotely activated using radio control devices;
to set the two functions to channels A-B-C-D use the selection
J3
1
2
close-block open-close
Memory module (MM)
This is extractable, furnished with a non volatile EEPROM type
memory and contains the transmitter codes and allows you to
memorise up to 300 codes. The programmed codes are main-
tained in this module even during blackouts.
Note: Before memorising the transmitters for the first
time remember to cancel the entire memory content.
If the electronic card has to be replaced due to failure,
the module can be extracted from it and inserted into
the new card. Make sure that the module is correctly
inserted as shown on page 8, 9.
Signal LEDs "L4" (pages 8, 9):
Flashing quickly: cancels a single code
Flashing slowly: memorises a single code
Permanently lit: memory full.
TRANSMITTER CODE MANAGEMENT
Memorising a channel (pages 8, 9):
flash slowly.
2) At the same time activate the transmitter which is to be memo-
rised.
P2 MEMO
again.
P2 MEMO button: The LED will continue to
flash.
5) Activate the transmitter again (same transmitter, same chan-
nel; if the channel is different or it is a different transmitter the
memorisation attempt will abort without success).
indicating that the transmitter has been correctly memo-
rised.
Note: It is not possible to memorise a code which is already in
memory: if you attempt this, the LED will switch off when you
activate the transmitter (point 2).
continue the memorising procedure. If after activating the trans-
mitter for the first time you wait for more than fifteen seconds
without activating the transmitter a second time the memorisation
attempt will abort without success.
Cancelling a channel (pages 8, 9):
flash quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LED will remain lit for 2 s, indicating that the transmitter
has been cancelled.
Note: If the user that you wish to cancel is not in memory, the
you be able to continue the cancellation procedure.
For both the memorisation and cancellation procedures, if the
button is released before activating the transmitter the procedure
will abort.
SEQUENTIAL COMMAND;
BLOCK COMMAND;
1 open-block-
P2 MEMO L4
L4
L4
P2 MEMO will you be able to
P3 DEL L4
P3
Cancelling all user codes from memory (pages 8, 9):
four seconds.
L4
(about 8 seconds).
L4
terminated.
Note: When the memory is almost full the time required to search
for a user code could take up to 1 second from when the com-
mand was received. If led "L4" remains lit memory is completely
full. To memorise a new transmitter you will first have to cancel
a code from memory.
Memorising ulterior channels via radio
2. Using a transmitter, in which at least
has already been memorised in the
receiver, press the button in the
transmitter as shown in figure.
Note: all the receivers within range when the channel button is
pressed (and which have at least one of the transmitter channel but-
3. Press one of the channel buttons on the same transmitter. The
receivers which do not contain that channel code will sound a
which contain the channel code will sound a one-second long
4. Press the previously chosen channel buttons on the transmitter
of half a second each after which the receiver will be ready to
receive another code.
5. To leave the programming mode wait for 3 seconds without
pressing any buttons. The receiver will sound a five-second
Note: When the memory is entirely occupied the buzzer will sound
via radio L4
via radio

CONNECTING THE ANTENNA

Connect an ANS400 tuned antenna using a coaxial cable RG58
(impedance 50 ) with a maximum length of 15 m.

FUNCTION MODES

1) Automatic
This is selected by enabling automatic reclosing (dip "2" in position
"ON"). Starting from the completely closed position the sequential
command starts a complete function cycle that terminates with
automatic reclosing.
Automatic reclosing starts after the programmed pause period has
elapsed when the opening cycle has been completed or straight
away after the intervention of a photoelectric cell (the intervention
of a photoelectric cell causes the pause time to be reset).
During the pause time the symbol
pressing the blocking button during this period will stop automatic
reclosing and consequently stop the display from flashing.
Note: the courtesy light switches on each time a movement
command is given (both via cable or via radio) and switches off
30 seconds after the manoeuvre has been completed.
25
P2+P3
J3
J3
A, B, C or D
B1
programming via radio" mode.
programming
programming
will flash on the display and