Connecting The Antenna; Function Mode - Cardin Elettronica SL Serie Mode D'emploi

Masquer les pouces Voir aussi pour SL Serie:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

REMOTE CONTROL (fig. 3, page 4)
The system can be remotely activated using radio control devices. Each
channel can be set to a maximum of 2 functions:
- function 1: sequential command
- function 2: limited opening command
To set one of the functions to the channels A-b-C-D use the selection
jumpers "J1":
- In position "A" the first function is active, TD;
- In position "b" the second function is active TAL.
The command can be set (dip "1") to work as "open-block-close-
block" or "open-close".
Memory module (M1)
This is extractable, furnished with a non volatile EEPROM type memory
and contains the transmitter codes and allows you to memorise up to
300 codes.
The programmed codes are maintained in this module even during
blackouts.
Note: Before memorising the transmitters for the first time remember
to cancel the entire memory content.
If the electronic card has to be replaced due to failure, the module can
be extracted from it and inserted into the new card. Make sure that the
module is correctly inserted as shown in fig. 3.
Signal LEDs "L3" (fig. 3):
Flashing quickly:
cancels a single code
Flashing slowly:
memorises a single code
Permanently lit:
memory full.
TRANSMITTER CODE MANAGEMENT
Memorising a channel (fig. 3):
1. Press and hold down button "P1" MEMO: The LED "L3" will flash
slowly.
2. At the same time activate the transmitter which is to be memo-
rised.
3. Hold down button "P1" MEMO until LED "L3" starts to flash
again.
4. Release the button: The LED will continue to flash.
5. Activate the transmitter again (same transmitter, same channel; if the
channel is different or it is a different transmitter the memorisation
attempt will abort without success).
6. End of memorisation: the LED "L3" will remain lit for 2 seconds,
indicating that the transmitter has been correctly memorised.
Note: It is not possible to memorise a code which is already in memory:
if you attempt this, the LED will switch off when you activate the trans-
mitter (point 2).
Only after releasing the button "P1" MEMO will you be able to continue
the memorising procedure.
If after activating the transmitter for the first time you wait for more
than fifteen seconds without activating the transmitter a second time
the memorisation attempt will abort without success.
Cancelling a channel (fig. 3):
1. Press and hold down the button "P2" DEL: the LED "L3" will flash
quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LED will remain lit for 2 sec., indicating that the transmitter has
been cancelled.
Note: If the user that you wish to cancel is not in memory, the LED will
stop flashing; only after releasing the button "P2" will you be able to
continue the cancellation procedure.
For both the memorisation and cancellation procedures, if the button is
released before activating the transmitter the procedure will abort.
Cancelling all user codes from memory (fig. 3)
1. Keep both buttons pressed down ("P1+P2") for more than four
seconds.
2. LED "L3" will remain lit during the entire cancellation time (about 8
seconds).
3. LED "L3" switches off when the cancellation procedure has termi-
nated.
Note: When the memory is almost full the time required to search for
a user code could take up to 1 second from when the command was
received. If led "L3" remains lit memory is completely full. To memorise
a new transmitter you will first have to cancel a code from memory.
Memorising ulterior channels via radio
• Memorisation can be activated by radio (without opening the receiver
container) if jumper "J2" has been inserted (fig. 3).
1. Make sure that the jumper "J2" has been inserted (fig. 3).
2. Using a transmitter, in which at least one
channel button "A, B, C or D" has already
been memorised in the receiver, press
the button in the transmitter as shown
in figure.
Note: all the receivers within range when the channel button is pressed
(and which have at least one of the transmitter channel buttons memo-
rised) will activate their signal buzzer "b1" (fig. 3).
3. Press one of the channel buttons on the same transmitter. The receiv-
ers which do not contain that channel code will sound a five-second
long "beep" and will then deactivate. The receivers which contain
the channel code will sound a one-second long "beep" and will enter
the "programming via radio" mode.
4. Press the previously chosen channel buttons on the transmitter
which you wish to memorise; the receiver will sound 2 "beeps" of
half a second each after which the receiver will be ready to receive
another code.
5. To leave the programming mode wait for 3 seconds without pressing
any buttons. The receiver will sound a five-second long "beep" and
will then exit the programming mode.
Note: When the memory is entirely occupied the buzzer will sound
10 rapid "beeps" and will automatically leave the "programming via
radio" mode. Led "L3" will remain lit on the receiver.
The same signal is given each time you try to enter "programming via
radio" when the memory is full.

CONNECTING THE ANTENNA

Connect an ANS400 tuned antenna using a coaxial cable RG58 (imped-
ance 50Ω) with a maximum length of 15 m.

FUNCTION MODE

1) Automatic
Selected by enabling automatic reclosing (dip "2" in position "ON").
When the door is completely closed the opening command will start a
complete cycle which will end with automatic reclosing and the night
light switching off.
Automatic reclosing starts after the programmed pause period has
elapsed (minimum 2 seconds) when the opening cycle has been
completed or straight away after the intervention of a photoelectric
cell (the intervention of a photoelectric cell causes the pause time to
be reset).
During the pause time the symbol
ing the blocking button during this period will stop automatic reclosing
and consequently stop the display from flashing.
The indicator light remains lit until the closing manoeuvre has termi-
nated.
2) Semiautomatic
Selected by deactivating automatic reclosing (dip "2" in position "OFF").
Work cycle control using separate opening and closing commands.
When the door has reached the completely open position the system
will wait until it receives a closing command either via an external control
button or via radio control, before completing the cycle.
The indicator light remains lit until the closing manoeuvre has termi-
nated.
20
All rights reserved. Unauthorised copying or use of the information contained in this document is pun
Description :
MEMORIZZAZIONE CODICE Tx-Rx
Drawing number :
DM0531
Product Code :
RCQ449100
Draft :
P.J.Heath
Date :
13-04-2001
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/4018
will flash on the display and press-

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

101/sl424ebss

Table des Matières