ATIKA HHS 710/56 Notice Originale page 19

condition that may affect the power tool's operation. If
damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Safety instructions for hedge trimmers
 Keep away all body parts from the cutting blades. Do not
attempt to remove cut material or to hold material to be
cut while the cutting tool is in operation. Only remove
jammed material after the unit was switched off. A single
moment of inadvertence when using the hedge shear may
result in severe injury.
 Make sure that all protective devices and handles are
attached before using the unit. Never attempt to put into
service an incomplete unit or a unit that was improperly
modified.
 Carry the hedge shear on its handle with the cutting tool
stopped. Always install the guard when transporting or
storing the hedge shear. A careful handling of the unit
minimises the risk of injury by the cutting tool.
 Always hold the power tool on the insulated handle
surfaces as the cutting blades may come into contact
with hidden power cables or the unit's mains supply
cable. A contact of the cutting blades with a live conductor
may apply hazardous voltage to metallic parts of the unit and
cause electric shock.
 Keep the cable away from the cutting area. During the
work, the cable may be hidden by shrubbery and accidentally
cut.
 This device is not intended to be used by persons (including
children) with restricted physical, sensory or mental abilities
or a lack of experience and/or know-how unless they are
supervised by a person responsible for their safety or they
have been instructed by such a person on the use of the
device.
Supervise children to make sure they do not play with the
device.
more safety warnings
„Electrical safety"
 Design of the connection cable according to IEC 60245 (H
07 RN-F) with a core cross-section of at least
 1.5 mm² for cable lengths up to 25 m
 2.5 mm² for cable lengths over 25 m
 Long and thin connection lines result in a voltage drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
 Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
 The connector of the connection cable must be splash-proof.
 When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
 During the cutting operation, the supply cord must be
securely positioned to prevent the cord from snagged on
branches and the like.
 Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges.
 Wind off completely the cable when using a cable drum.
 Regularly check the cables and replace them if they are
damaged.
 Do not use any defective connection cables.
 Do not set up any provisional electrical connections.
 Do not hose down the device with water. (origin of danger
electric current).
 Never bypass protective devices or deactivate them.
 Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
 The electrical connection or repairs to electrical parts of the
machine must be carried out by a certified electrician or one
of our customer service points. Local regulations – especially
regarding protective measures – must be observed.
more safety warnings
„Personal safety"
 The operator is responsible to third persons within the area
of operations.
 Adhere to national regulations that might specify an age limit
for the user of the unit.
 Wear suitable protective equipment when working:
 hairnet in case of long hair
 protection gloves
 eye and ear protection
more safety warnings
„Power tool use and care"
 Do not modify the device or parts of the device respectively.
 After a longer period of use, accessible metallic parts and
accessories may be hot.
 Switch off the machine and pull the mains plug from the
socket and make sure that all moving parts have come to a
complete standstill before:
the cutting tool comes into contact with soil, stones, nails
or other foreign objects ( check whether the cutting
tool/machine is damaged)
Carrying out repair work.

 Performing maintenance and cleaning work.
Removal of faults (including blocking of knives).

 Transport.
 Leaving the machine
interruption).
(also during temporary
19