Güde 01976 DHH 1100/13 TZ Traduction Du Mode D'emploi D'origine page 15

The knife forward movement is reduced to the splitting pace
with maximum performance being achieved by full pressing
down.
CAUTION: Never split with the fast forward movement! Press
the operating levers down to the stop when splitting.
Blocks/splitting table
Optionally available:
Matching short wooden table for hanging.
Güde Article No: # 02017
• Put the splitting knife down to 5 cm above the block table.
•
Release the operating lever and switch the splitter off.
•
Perform corresponding adjustment (pic. 13).
Split wood length
The hydraulic wood splitter is suitable for splitting blocks (fitted
splitting table) and one-metre woods. The maximum stroke
can be limited (see the Stroke limitation).
The effective upward stroke limitation is app. 3 – 5 cm above
the wood.
RISK OF INJURY!
The splitting table is put to the operating position and
blocked with a split pin for splitting blocks (pic. 5). Now
put the limit switch of the splitting table to the central
position using a split pin on an adjusting rod (pic. 17; pic.
14). To that end, use the bush (pic. 15; pic. 16).
If the split pin is locked properly, the splitting knife stops
app. 5 cm before the splitting table (pic. 18)
Maintenance and treatment
Safety instructions for inspections and maintenance:
Only a regularly maintained and treated appliance can be a
satisfactory aid. Insufficient maintenance and care may lead to
unexpected accidents and injuries.
• Never use aggressive cleaning agents for cleaning.
They could damage or destroy the appliance.
•
Unplug the appliance (1977).
•
Have any repairs and maintenance of the electric device
performed only by electricians.
•
All protective and safety equipment must immediately be
refitted after repair and maintenance are finished.
We recommend the following:
•
Splitting knife
The splitting knife is subject to quick wear that must be
additionally ground down if necessary. This will increase
the splitting performance and protect the splitter. Tip:
grease the splitting knife!
•
Two-handed protective equipment
Running of the combined holding and switching device
must be smooth. Occasionally, it can be lubricated by a
few oil drops.
•
Moving parts
Keep the splitting knife guide clean (off any dirt,
splinters, bark, etc.) Lubricate the skids with fat.
•
Hydraulic equipment
Check the hydraulic connections and screwing if tight
and not worn. Tighten the screwing if necessary.
Change oil once a year (pic. 11):
• Check the oil level (appliance must be put even). The oil
tank is located in the splitter column and has been filled
with high-quality hydraulic oil by the manufacturer.
• There are 2 socket-head screws on the splitter column.
The bottom one is used for oil draining (when changing
oil) and the upper one for checking the oil level. The oil
level must reach up to the upper socket-head screw.
• Screw out the oil drain screw (pic. 11/1).
• Catch the drained oil (different quantity in each model)
• Dispose the drained oil in an environment friendly manner
• Screw up the oil drain screw again. Caution! No dirt
must get to the oil tank.
• Add the hydraulic oil up to the upper socket-head screw
(pic. 11/2)
• Test the wood splitter with no load several times.
Recommended hydraulic oil: DIN ISO HLP 46
Güde Art. No. 42004
Viscosity: 46
Oil quantity: (see the Technical specifications)
Functional test
The hydraulic wood splitter is supplied in an operable
condition. The following functional tests must be carried out
before each use.
•
Let both switching handles and the splitting knife go down
to app. 5 cm above the table
• One switching handle must always be released; the
splitting knife will remain in the selected position
•
#01977: STOP switch The switch combination drop
lid switches the electric drive off. The red area on the
yellow background signals emergency shutdown
function. To be used in case of danger only! Please
advise other persons of this protective equipment.
15