Power Mode; Temperature Mode - Steba IK 60 E Mode D'emploi

Operation:
The appliance is equipped with a touch control display- All functions will be
activated by touching the surface.
Plug the appliance into the socket. A sound can be heard and all LED and the display
are on for one second. Now the appliance is in stand-by modus. Place a suitable pot in
the middle of the cooking area (min. diameter 12cm). When the ON/OFF
for one time a LED bellow heating is on and one LED is on above the ON/OFF
Attention!!! After 30seconds the appliance will go back into the stand-by modus,
when no function by touching was chosen.

Power mode

This function is suitable for boiling water and soups.
Place the pot in the middle of the cooking area.
Touch ON/OFF one time and after that the function
(Zeichen) is on and in the display there is 1200 is shown. The cooling fan starts work-
ing. With the buttons or can the power be adjusted in steps of 200W. (200Watt
– 2000Watt)
During cooking the Wattage can be changed at any time.
The unit is equipped with an overheat protection. When the pot gets too hot, the
appliance will stop working, a sound can be heard and in the display E02 can be seen.
In that case, press the ON/OFF and cool the appliance down for some minutes. The
appliance will work after that without any problem.
When the failure code E0 is in the display then the used pot or pan is not
suitable induction cookers. The appliance beeps 9 times and after
ca 1 minute the appliance will switch to the stand-by mode.

Temperature mode

This function is suitable for roasting meat and vegetables.
Place the pot in the middle of the cooking area.
Touch ON/OFF one time and after that 3 times the function button
bellow the temperature symbol and in the display 180 can be seen. The cooling fan
starts to work. With the buttons
degree steps. During the cooking the temperature can be adjusted at any time. The
build in sensor keeps the temperature at about the adjusted temperature. The tem-
perature can be adjusted from 60°C up to 240°C.
When the failure code E0 is in the display then the used pot or pan is not
suitable induction cookers. The appliance beeps 9 times and after
ca 1 minute the appliance will switch to the stand-by mode.
10
480-13228 - IK60E - 07-2011.indd 10-11
is touched
, the red LED bellow Heating
. A red LED
or the temperature can be adjusted in 20
Timer
The temperature or power must be adjusted first, as described above. Touch the func-
tion button so many times, until the red LED bellow the Timer symbol
The display shows „0". Now there is 5 seconds time to adjust the time by pressing the
button in steps of 5 minutes. The time can be adjusted from 5 to 180min. Pressing
the button decreases the time by 5 minutes. When the
. one time the time increases or decreases by 5 minutes and a beeping noise can be
heard. When the
heard and the time can be adjusted faster.
If you want to change the time during the cooking touch the function
button
change the timer setting.
When the function temperature and the timer is used and it is the intention to switch
to the power mode, then the Timer is not deleted.
When the ON/OFF button
deleted and the appliances switches to the stand-by mode.
If the adjusted time runs out, the appliance will switch to the stand-by mode.
Residual heat „H"
When the glass plate gets hotter than ca 60°C the residual heat symbol „H" can be
seen in the display and vanishes after the glass plate cools down. When the residual
heat light „H" is on, then do not touch the cooking area. Danger of burns!!!
Please notice that the cooling fan is running during cooking to cool down the elec-
tronic inside.
To protect the electronic the cooling fan will work some minutes after the appliance
is switched off. This avoids that the appliance do not overheat and be damaged. Only
unplug the appliance after the cooling fan switched off by itself.
Child lock
By pressing the button
How to Clean
∙ Disconnect plug and wait until it is cooled down. Clean after each use.
∙ Never immerse the device in Water.
∙ If the pots/pans are used without being cleaned, discoloration or cooked on stains
may be caused.
∙ Do not use petrol, thinner, scrubbing brush or polishing power to clean the induc-
tion cooker.
∙ Wipe using dish washing agent and damp cloth.
∙ Use vacuum cleaner to suck up dirt from the air intake and exhaust vent.
∙ Never run water over the unit. (water gets inside may cause malfunction).
or
or is pressed for a longer period no beeping sound can be
until the timer LED is blinking. Now you have ca 5 seconds time to
is touched during the cooking then the program will be
the child protection will be activated or deactivated.
is blinking.
button is pressed
11
22.07.2011 10:03:13