Sliding Flange With Additional O-Ring Seal; Oil Flow Meter And Operating Hour Meter; Screw Plug For The Return Flow Connection Of The Plug; Service Case - herrmann HL 60 G-S Caractéristiques Techniques, Instructions De Montage Et De Service

10.6 Sliding flange with additional O-ring seal

In order to satisfy the highest requirements with regard to odorous sub-
stances at the interface between the burner and the heat generator, we
recommend the employment of a sliding flange with an additional O-ring
seal. In order to achieve a maximum level of density the standard existing
boiler-side flat seal is supplemented by an additional O-ring seal. The in-
stallation of this alternative flange connection may be carried out factory
finished or by using the mixing device depending subsequently specified
conversion sets.
Order no. 10003.00172 for the mixing devices G/I/K (burner tube Ø80 mm)
or order no. 10003.00173 for the mixing devices N/P (burner tube Ø100
mm).
Sealing for flange plate
boiler side
(standard sealing)
Sealing guide ring
O-ring
(additional
sealing)
8
9
1 0
1 1
1 2
1 3
1 4
Conversion set consists of:
1 Flange clamp burner side
2 Hexagon nut DIN 934 M8
3 Flange plate boiler side, S1
4 O-ring
5 Countersunk screw, DIN 965 M3x5 10023.00043
6 Sealing guide ring
7 Gasket for flange plate boiler side
8 Cylinder screw, DIN 7984 M8x13
9 Cylinder screw, DIN 7984 M8x30
10 Washer, DIN 125 8,4A
11 Gasket for flange clamp burner side 10006.00007
12 Hexagon nut DIN 934 M8
13 Cylinder screw DIN 7984 M8x30
14 Washer DIN 125 8,4A
Flange plate,
boiler side S1
Flange clamp
burner side
Burner pipe
1
2
3
4
5
6
G/I/K (Ø80mm) N/P (Ø100mm)
10002.00114 10002.00116
10023.00002 10023.00002
10002.00141 10002.00142
10006.00108 10006.00059
10023.00043
10004.00328 10004.00362
10006.00003 10006.00126
10023.00063 10023.00063
10023.00008 10023.00008
10023.00020 10023.00020
10006.00007
10023.00002 10023.00002
10023.00008 10023.00008
10023.00020 10023.00020

10.7 Oil flow meter and operating hour meter

For acquisition of the used quantity of heating oil and the running period
of the burner, we offer you the installation of a combination of oil flow me-
ter and operating hour meter. The installation of the oil flow meter and
operating hour meter may be carried out factory finished, or by using the
subsequently specified conversion set (order no.: 10003.00019).
This consists of:
1 Display of oil flow meter
2 Cable oil firing unit - display oil meter
3 Cable transducer - display oil meter
4 Cover hood for burner with oil meter
5 Oil pressure line, long
6 Straight screw-in joint
7 Sealing ring
8 Transducer oil flow meter
9 Swivelling screw fitting, including sealing ring
10 Oil pressure line, short
3
7
10.8 Screw plug for the return flow connection of the
pump
To put the oil pump into one-line operation the return flow connection of
the pump has to be closed by a screw plug (order no.: 100019.00006).
Furthermore the shift screw in the junction canal between pressure and
suction side has to be removed (see Chapter 3.5).

10.9 Service case

In order to have all necessary spare parts ready for an on-site service on
the burner we offer you an individual service case for the respective burner
and your requirements.
Please do not hesitate to contact us for further information.

11. Customer service

For further information on the burner and for ordering spare parts please
do not hesitate to contact our Customer Service Department at:
Herrmann GmbH u. Co. KG
Phone: 00 49 7151 98928-0, Fax: 00 49 7151 98928-49
Email: info@herrmann-burners.de
1
2
4
10
6
7
8
9
EN
41
10030.00005
10013.00030
10013.00031
10001.00008
10018.00006
10017.00010
10017.00007
10030.00006
10017.00009
10018.00007
5