Explosion Hazard; Important Safety Information - Hatco GLO-RAY GR2SD Série Manuel D'installation Et D'utilisation

English
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
WARNING
ELECTRIC SHOCK HAzARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install the proper voltage
and size electrical receptacle.
• units supplied without an electrical plug require field
installation of proper plug. Plug must be properly
grounded and of
configuration for electrical specifications of unit.
Contact a qualified electrician to determine and install
proper electrical plug.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any maintenance or
cleaning.
• DO NOT submerge or saturate with water. unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. The cord must be replaced by Hatco, an
Authorized Hatco Service Agent, or a person with
similar qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAzARD: Locate unit a minimum of 2" (51 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.

ExPLOSION HAzARD:

other flammable vapors or liquids in the vicinity of this or
any other appliance.
Make sure food product has been heated to the proper food-
safe temperature before placing on the unit. Failure to heat
food product properly may result in serious health risks. This
unit is for holding preheated food product only.
Form No. GR2SDm-0316
correct voltage, size,
Do not store or use gasoline or

IMPORTANT SAFETy INFORMATION

This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized Hatco Service
and
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.
BuRN HAzARD: Some exterior surfaces on unit will get
hot. use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. The location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36" (914 mm) in width or weighing more than 80
lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point of
use, 4" (102 mm) legs are included to allow for proper
cleaning access below unit.
Only light bulbs which meet or exceed NSF standards,
specifically designed for food holding areas must be used.
Breakage of light bulbs not specially coated could result
in personal injury and/or food contamination.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch the finish of the unit,
marring its appearance and making it susceptible to soil
accumulation.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
IMPORTANT — DO NOT use paper towel or glass cleaner to
clean polycarbonate surfaces. Paper towel and glass
cleaner may scratch the material. Wipe off polycarbonate
surfaces using a soft, clean, water-dampened cloth.
Do not slide pans across hardcoat surface, use rough-
bottomed pans, or drop anything on hardcoat surface.
Scratching may occur. Damage to hardcoat surface caused
by misuse is not covered under warranty.
Transport unit in upright position only. Before moving or
tipping unit, remove or secure all glass surfaces with tape.
Failure to do so may result in damage to unit or personal
injury.
3
WARNING
CAUTION
NOTICE