Important Safety Information; Fire Hazard - Hatco HBG Série Manuel D'installation Et D'utilisation

Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property
WARNING
ELECTRIC SHOCk HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or
maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 21°C (70°F).
• Remote mounted control panel must be mounted on a
vertical wall and installed in vertical position. Mounting
control panel in horizontal position may result in
collection of liquids and lead to an electric shock.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by Hatco, an Authorized
Hatco Service Agent, or a person with similar
qualifications.
• Do not clean unit when it is energized or hot.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD: Locate unit a minimum of 25 mm (1") from
combustible walls and materials. If safe distances are not
maintained, combustion or discoloration could occur.
Make sure food product has been heated to the proper
food-safe temperature before placing on the unit. Failure to
heat food product properly may result in serious health
risks. This unit is for holding preheated food product only.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
414-671-6350; fax 414-671-3976.

IMPORTANT SAFETy INFORMATION

BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent unit
or its contents from falling accidentally and strong enough
to support the weight of the unit and contents.
Do not operate built-in models without control box
mounted properly as described in the installation
instructions.
The National Sanitation Foundation (NSF) requires that
units over 36" (914 mm) in width or weighing more than 80
lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point of
use, 4" (102 mm) legs are included to allow for proper
cleaning access below unit.
Pitting or indentation in glass surface may occur from
sugary spills. If pitting or indentation occurs, glass surface
must be replaced. To prevent further damage and possible
injury from broken glass, stop using unit immediately and
contact an Authorized Hatco Service Agent.
Built-in units are designed for use in metallic countertops.
Damage to non-metallic countertop material is not covered
under the Hatco warranty.
Do not modify wiring or cut thermostat capillary wire on
control box to increase remote mounting distance. Cutting
thermostat capillary wire will cause unit to overheat and
may damage unit as well as surrounding countertop.
Do not turn on unit until it has been cleaned thoroughly.
Ceramic glass surface must be clear of debris to prevent
burn-on.
Do not lay unit on the side with the control panel or damage
to the unit could occur.
Do not slide pans across glass surface, use rough-
bottomed pans, or drop anything on glass surface.
Scratching or breakage may occur. Damage to glass
surface or breakage of glass caused by misuse is not
covered under warranty.
Use only wipes, pads, and cleaners designed specifically
for cleaning ceramic glass surfaces. Using other wipes,
pads, or cleaners may damage ceramic glass surface.
.
CAUTION
NOTICE