Before Use; Attaching The Round Handle; Assembling The Quick Release Mechanism; Fixing/Attaching The Carrying Harness - FLORABEST FBK 4 B2 Traduction Du Mode D'emploi D'origine

Before use

CAUTION!
■ Always wear non-slip footwear and appropriate safety clothing
such as protective gloves, a hard hat, a protective mask and safety
goggles as well as hearing protection.
■ Check the area in which the appliance is to be used and remove any
objects that may be caught and slung away.
■ Before use and after dropping or other impacts, always visually in-
spect the appliance to check whether the cutting tool, mounting bolts
and the entire cutting unit are damaged. Worn or damaged cutting
tools and mounting bolts must be replaced.
■ Always carry out a visual inspection before use to check whether the
cutting tools are worn or damaged. To prevent imbalance, worn or
damaged cutting tools and mounting bolts should be replaced only
as complete sets.

Attaching the round handle

♦ Start by fitting the rubber ring
♦ Attach the barrier bar onto the rubber ring
shown in the diagram.
♦ The pin of the barrier bar
5
b
holes on the boom to lock into place.
♦ Push the round handle onto the rubber ring
boom .
♦ Insert the 4 mounting bolts
and fix them onto the barrier bar
♦ Tighten the screws .

Assembling the quick release mechanism

♦ Hook in the carabiner and secure it with the red strap on the quick
release mechanism (see figures). Pull on the red strap if you have to
put down the appliance quickly.

Fixing/attaching the carrying harness

♦ Hook the carrying harness
♦ Adjust the length of the carrying harness
carrying lug is at hip height when the strap is hooked in place.
│ GB │ IE │ NI
■ 10
on the boom .
5a
from below, as
5a
must be pushed into one of the two
provided on the
5a
from above through the round handle
with the 4 nuts.
into the carrying lug .
to your size so that the

Assembling the hedge trimmer

♦ Start by undoing the screw grip
♦ Push the pin on the front boom
hedge trimmer into the groove on the engine
unit boom
correctly inserted, the red line must match
up with the one on the engine unit boom.
♦ Tighten the screw grip .
NOTE
► Assembly of the pole pruner/strimmer/3-section cutting blade/exten-
sion attachment is carried out in the same order.

Removing the hedge trimmer

♦ Undo the screw grip and pull the front boom
out of the engine unit boom
NOTE
► Removal of the pole pruner/strimmer/3-section cutting blade/extension
attachment is carried out in the same order.

Swivelling the hedge trimmer

♦ Release the lock/release .
♦ Press the control lever and swivel the hedge trimmer into the desired
position.
♦ Allow the control lever to click into the recess in the base plate
(hedge trimmer) .

Mounting the saw chain and blade

WARNING!
► Wear protective gloves! There is a danger of injury from the sharp
cutting teeth!
NOTE
► Pay close attention to the running direction of the saw chain
the blade and at the base plate (hedge trimmer)
► Depending on wear, the blade
♦ Undo the nut using the open-ended spanner
♦ Remove the sprocket cover
♦ Lay the saw chain over the blade
♦ Now fit the blade and saw chain
♦ Lay the guide rail over the blade guide
tensioner pin in the blade hole
chain over the chain sprocket
♦ Now you can tighten the saw chain
checking the saw chain").
♦ Replace the sprocket cover

Removing the saw chain

♦ You may have to loosen the saw chain
and the saw chain (see section "Tightening and checking the saw
chain"). Follow these instructions in reverse order.
on the boom of the engine unit.
of the
as far as the stop. Once it is
of the hedge trimmer
.
can be turned.
.
.
starting at the tip.
.
, while inserting the chain
. At the same time, lay the saw
.
(see section "Tightening and
and tighten the nut gently.
to remove the blade
FBK 4 B2
on
.