Further safety instructions
CAUTION! RISK OF INJURY!
►
To prevent injuries, do not touch the appliance above the protective
ring
while the appliance is running.
■
Children should be supervised to ensure that they do not play with the
appliance.
■
It is necessary to have training before the usage of this tool.
■
Damaged power cords, connectors and plugs or non-compliant extension
leads may not be used. If the mains cable is damaged or cut, unplug
the appliance from the mains immediately.
■
Do not work with a damaged or incomplete appliance or an appliance
that has been modifi ed without the consent of the manufacturer. Never
use the unit with defective protective equipment. Do not use the appliance
if it has a defective on/off switch. Before use, check the security state of
the appliance, especially the blade and the saw chain. If the appliance
has been dropped, check for signifi cant damage or defects.
■
Never start the appliance before the blade, saw chain and sprocket
covers have been fi tted correctly.
■
When starting and operating the appliance, ensure that it does not
come into contact with the ground, stones, wire, other foreign material.
Switch the appliance off before you put it down.
■
Do not cut any wood that is lying on the ground and do not attempt to
saw roots that are protruding from the soil. Avoid immersing the saw
chain in the soil at all costs, as this could blunt the saw chain.
Original accessories/auxiliary equipment
■
Use only the additional equipment and accessories detailed in the
operating instructions. The use of tools and accessories other than
those recommended in the operating instructions could lead to an
increased risk of personal injury for you.
Before initial use
CAUTION! RISK OF INJURY!
►
Before any work on the appliance, disconnect the plug.
Danger of electrical shocks.
Motor unit
Attaching the round handle
♦
Place the round handle
in the desired position on the boom
♦
Tighten the screw
.
Fitting the quick release mechanism
♦
Hook in the carabiner and secure it with the red strap on the quick
release mechanism (see fi gures). Pull on the red strap if you have to
release the appliance quickly.
Fixing/attaching the shoulder strap
♦
Hook the shoulder strap
into the carrying eyelet
♦
Adjust the length of the shoulder strap
eyelet
is at hip height when hooked in place.
FHEHS 900 A1
Mounting the hedge trimmer
♦
♦
♦
Mounting the pole pruner
♦
♦
♦
Swivelling the hedge trimmer
♦
♦
♦
Swivelling the pole pruner
♦
♦
♦
Mounting the saw chain and blade
.
♦
♦
♦
♦
♦
♦
♦
♦
.
to your size so that carrying
Push the front boom
of the hedge trimmer to the boom
motor unit.
The locking pin
must engage.
Secure the two booms
with the tommy screw
the nut
on the opposite side.
Push the front boom
of the pole pruner to the boom
unit.
The locking pin
must engage.
Secure the two booms
with the tommy screw
the nut
on the opposite side.
Release the lock/release
.
Press the control lever
and swivel the hedge trimmer into the
desired position.
Allow the control lever
and the locking/release
recess in the base plate (hedge trimmer)
Release the lock/release
.
Press the control lever
and swivel the pole pruner into the desired
position.
Allow the control lever
and the locking/release
recess in the base plate (pole pruner)
WARNING!
►
Wear protective gloves! There is a danger of injury from the sharp
cutting teeth.
NOTE
►
Pay close attention to the running direction of the saw chain
the blade
and at the sprocket cover
►
The blade
and the saw chain
►
Depending of wear and tear, the blade
Loosen the nut
with the mounting tool
Remove the sprocket cover
.
You may have to relax the saw chain
and the saw chain
. (see section Tightening and checking the saw
chain). Follow these instructions in reverse order.
Remove the blade
with the saw chain
Reset the saw chain
starting at the top of the blade
Lay the guide rail
over the blade guide
tensioner pin
in the blade hole
chain
over the chain sprocket
Now you can tighten the saw chain
checking the saw chain).
Replace the sprocket cover
of the
; to do this, fi t
of the motor
; to do this, fi t
to click into the
.
to click into the
.
.
are already installed on delivery.
can be turned.
.
to remove the blade
from the base plate
.
, while inserting the chain
. At the same time, lay the saw
.
(see section Tightening and
and tighten the nut
gently.
GB
on
.
43