Tightening And Checking The Saw Chain; Lubricating The Chain; Sharpening The Saw Chain; Attaching The Extension Attachment - FLORABEST FBK 4 B2 Traduction Du Mode D'emploi D'origine

Tightening and checking the saw chain

WARNING!
► Wear protective gloves! There is a danger of injury from the sharp
cutting teeth!
♦ Turn the chain-tensioner screw
flat-blade screwdriver to increase the tension.
♦ The saw chain must lie against the underside of the blade. Check
whether the saw chain can be drawn over the blade
NOTE
► A new saw chain stretches and must be tightened more frequently.

Lubricating the chain

♦ Remove the oil filler cap .
♦ Fill the oil tank with approx. 100 ml of organic chain oil
♦ The chain lubrication can be increased or decreased using the oil
adjusting screw .
♦ Press and then turn the oil adjusting screw
the chain lubrication.
♦ Press and then turn the oil adjusting screw
the chain lubrication.
WARNING!
► Never work without lubricating the chain first!
If the saw chain runs dry, the cutting equipment may become irrepar-
ably damaged within a short time. Always check chain lubrication
and oil level in the tank before starting work.
NOTE
► Use only saw chain oil. Preferably biodegradable. Do not use waste
oil, motor oil, etc.
► While working, check whether the chain lubrication is working
correctly.

Sharpening the saw chain

NOTE
► A bench grinder can be attached to the bench grinder support
a secure grip during grinding.
► You will find detailed information on sharpening in a sharpening set,
e.g. from Oregon.
► Alternatively, you can use an electrical saw chain sharpening device
and follow the manufacturer's instructions.
► If you have any doubts about carrying out the work, the saw chain
should be replaced.

Attaching the extension attachment

CAUTION!
■ Do not use the extension attachment/boom
the 3-section cutting blade/strimmer attachment!
NOTE
► Use the extension attachment/boom
heights.
♦ Fit the extension attachment/boom
the hedge trimmer/pole pruner. The assembly is carried out in the
same manner as for the attachments described previously.
FBK 4 B2
in a clockwise direction using the
by hand.
.
clockwise to decrease
anticlockwise to increase
in combination with
for working at greater
between the engine unit and

Fitting/removing the protective guard

WARNING!
■ When working with the 3-section cutting blade
must be fitted. The blade guard
of the boom . The blade guard
with the 2 screws
Cutting equip-
ment
3-section cutting blade
Strimmer
WARNING!
► Do not use any other cutting equipment apart from that which is
supplied with the product. The use of any other cutting equipment
or protective equipment is deemed to be improper and carries a
significant risk of accidents.

Installing/replacing the cutting blade

■ Fit/remove the 3-section cutting blade
■ Find the hole in the drive plate
block it with the supplied hex key
■ Place the 3-section cutting blade
The inscription must be visible from above when holding the tool in the
working position (see fold-out page). Both sides of the 3-section cutting
blade can be used.
■ Fit the pressure plate
1c).
■ Fit the pressure plate cover
■ Tighten the nut with the spark plug spanner
TUNG! Left-hand thread! (see fig. 1f).
■ The 3-section cutting blade
This must be removed before use and refitted during periods when not
in use.
■ The plastic cover can now be removed.
CAUTION! SHARP EDGES, WEAR PROTECTIVE GLOVES
■ Fit the cutting filament protective guard
for ■ The cutting filament protective guard
with the cutting filament. The cutting filament protective guard
(pre-fitted on delivery) is fitted as shown in figure 2a.
■ Ensure that the cutting filament protective guard
into place. There is a blade
tective guard . This is covered with a safety cover
C
■ Remove the safety cover
finishing work.
CAUTION! SHARP EDGES, WEAR PROTECTIVE GLOVES
■ To remove the cutting filament protective guard
guard , take a tool, such as a screwdriver, to carefully remove the
three mounting pins.
ATTENTION! RISK OF INJURY!
, the blade guard
is positioned under the metal panel
is now attached to the front boom
. To do this, use the supplied hex key
Protective equipment
Blade guard
Blade guard + cutting filament protect-
ive guard
C
as shown in figures 1a–1f.
, align it with the opposite hole and
.
on the drive plate
over the thread over the splined shaft (see fig.
(see fig. 1d).
anticlockwise ACH-
is fitted with a plastic cover on delivery.
on the protective guard
C
must be fitted when working
C
is correctly clicked
C
on the inside of the cutting filament pro-
A
(see fig. 2a.).
B
before starting work and replace it after
B
from the protective
C
GB │ IE │ NI │
.
(see fig. 1b).
.
C
11 ■