Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Preparing for first use
Press the OK key
to confirm.
y
Using the
key
and the
o
length of the entry delay (0 / 5 / 10 / 15 / 20 seconds).
Press the OK key
to confirm.
y
Wait 10 seconds until the device automatically quits
the settings mode.
Setting the date / time display:
1.
Enter the current password.
2.
Press the PROG key
a sufficient number of times
r
until the word "TIME" flashes at the top of the LC
display
.
w
3.
Press the OK key
to confirm.
y
4.
The LCD display now shows:
05 – 01 – 01
12 - 00
= year – Month – Day Hours - Minutes
5.
Select the appropriate field by pressing the OK key
the required number of times.
The selected field flashes.
6.
Using the
key
and the
o
desired setting.
7.
Press the OK key
to confirm.
y
8.
Repeat items 6 and 7 until all the values have been
entered.
9.
Wait 10 seconds until the device automatically the
settings mode.
Reset:
If you wish to delete all the settings or you have forgotten
your password, you can initiate a reset as follows:
Keep the PROG key
pressed until you hear a pip
r
sound.
Now immediately press the Pause key
hear a pip sound.
Now remove the battery and disconnect the mains
adapter. After 2 minutes insert the battery again
and/or reconnect the mains adapter.
42
GB
Now all the factory settings and the factory-installed
key
select the
password ("000") are restored.
i
Positioning the alarm unit
1.
Limiting the detection range/angle:
In the as-supplied condition the motion detector has a
detection angle of approx. 100 ° and detection range of
approx. 6 m (at a mounting height of 0.5 - 2 m) (see Fig. G).
you can modify the detection range and angle by adjusting
the motion detector.
To limit the detection angle use one of the two supplied
masking stickers
See Fig. H
Limited horizontal detection angle (approx. 40 °) e.g.
as a crossing detector.
See Fig. I
y
you can disable the motion detector by applying the
whole masking sticker, e.g. if detection is to be per-
key
select the
formed by an externally connected detector (see the
i
section on "Optional connections").
2. Positioning:
you can position the alarm unit upright or lying down.
If the surface is very smooth it is recommended that you
place the device lying down.
Placing the device lying down (see Fig. K):
Turn the motion detector
horizontally.
Place the alarm unit
Carefully turn the motion detector vertically into the
until you
desired direction (max. 90 °).
t
Mounting the device on a wall:
Find a suitable place to mount the device on a wall.
Before you fix the alarm unit
place, carry out the steps described in section 3
(complete or cut to size).
W
carefully through 180 °
{
down in the desired location.
Q
permanently into
Q
"Checking the functions" at the planned mounting site.
If the alarm and emergency telephone dialler is
functio ning properly, drill two suitable holes 27 mm
apart and horizontal (see Fig. L) at the planned lo-
cation.
Use the supplied screws
and dowels
E
device in place. The screw heads must be left pro-
jecting approx. 4 mm (see Fig. L) from the surface of
the wall.
Push the screw holes for mounting the device
to the screws until the alarm unit is firmly suspended
from the wall.
Connect the antenna
Connect the antenna
a to the antenna socket
Q
Turn the antenna into an upright position.
3. Checking the functions:
Checking that the remote control is functioning
properly
Press the
key on the remote control to arm the
alarm unit
.
Q
Arming is confirmed by three pips.
The LC display
of the alarm unit shows "ARM".
w
Disarm the siren unit by pressing the
the remote control.
Disarming is confirmed by one pip.
The word "ARM" disappears from the LC display
of the alarm unit.
Checking the emergency alarm:
The device has an emergency alarm function
(Panic function).
Press the panic key
on the remote control
:
The siren sounds for 30 seconds (if the siren is
switched on – see section "Switching the siren on / off")
and the programmed telephone numbers are called
(if the automatic dialling function is switched on –
to fix the
R
on
D
.
O
key
on
d
w
.
T
Publicité
Chapitres
Table des Matières
