Operation - Pentatech MA80 Mode D'emploi

see section "Switching automatic dialling on / off).
After 30 seconds pause the siren sounds for a sec-
ond time for 30 seconds.
To stop the alarm and the dialling process press the
key on the remote control.
d
The alarm unit sounds a pip and the alarm is now
switched off.
Checking the function of the motion detector:
Set the gong on / off switch on (setting "
]
gong sound sounds once.
After approx. 50 seconds delay the gong sounds again.
Now move into the range of detection of the motion
detector .
{
If the motion detector detects your motion the gong
sound sounds 2 x.
Set the gong on / off switch off (setting "
]
Checking the automatic dialling function:
Keep the PROG key pressed until you hear a pip
r
sound.
Now press a memory location number (number keys
"1" to"5"). The dialling unit now automatically
e
dials the associated assigned telephone number and
the telephone number flashes on the LC display
(assuming that the memory location has been as-
signed a telephone number).
Wait until the device automatically quits the dialling
process.

Operation

If you entered an incorrect password and confirmed it
with the OK key , the device responds with an "error
y
sound" and automatically returns to the normal mode.
Arming the alarm and emergency telephone dialler:
Arming with the remote control
Press the key
on the alarm unit
Enter the current password.
Press the OK key
y
The alarm unit sounds three pips and "ARM" ap-
pears at the bottom of the LC display
you now have approx. 55 seconds (exit delay) to
leave the monitored area without triggering the alarm.
After this exit delay has expired the device sounds a
pip.
I
"). The The alarm and emergency telephone dialler is now
armed.
Note: In the armed state the gong function is not activa-
ted, even if the gong On / Off switch
The alarm sounds - triggered by the detected motion
In the armed state the motion detector
0
"). motion.
The LED illuminates once briefly.
q
After the set entry delay expires:
If the alarm is triggered, the word "TRIGGER" appears
at the bottom of the LC display
The siren sounds for 30 seconds (if the siren is
p
switched on). After 30 seconds pause the siren sounds
for a second time for 30 seconds.
w
As determined by the automatic dialling function
(factory setting: dialling function switched on) and
the set number of dialling processes the alarm and
emergency telephone dialler dials all the stored tel-
ephone numbers in a cycle:
1st telephone number (30 sec.) - 3 sec. wait -
2nd telephone number (30 sec.) - 3 sec. wait -
3rd telephone number (30 sec.) - 3 sec. wait -
4th telephone number (30 sec.) - 3 sec. wait -
5th telephone number (30 sec.) - 3 sec. wait -
1st telephone number (30 sec.) - 3 sec. wait ....
etc.
If the person called accepts the call, he will hear an alarm
sound (even if the siren is switched off ) until the telephone
. connection is automatically stopped after max. 35 seconds
by the alarm unit.
. If the telephone connection of the dialling device and the
w
called telephone device have the features to enable the
caller display function to work then the telephone number
of the dialling device is displayed on the LC display of the
called telephone device. Even if one or more of the called
people accept the calls, all the telephone numbers (even
those who have already answered) are called for the set
number of dialling processes. The dialling cycle can only
I
is in setting " ". be interrupted by disarming the device.
]
If the alarm and emergency telephone dialler is not dis-
detects some armed during or after an alarm then it remains armed.
{
After the end of the siren process or at the end of the di-
alling cycle (but in any case not until at least 90 seconds
have elapsed) a new alarm can be triggered.
Disarming the alarm and emergency telephone dialler:
Disarming with the remote control
.
w
Press the
on the alarm unit
Note: Whilst the alarm unit is dialling a telephone
number, i.e. it is establishing a telephone connection, the
alarm and emergency telephone dialler cannot be dis-
armed using the keys on the device. The remote control
can be used to disarm the device at any time.
Preparing for first use
key
d
Enter the current password.
Press the OK key .
y
If appropriate, the alarm sound stops.
If appropriate, the flashing word "TRIGGER" disap-
pears.
The alarm unit sounds a pip.
The word "ARM" disappears from the LC display
The alarm and emergency telephone dialler is now
disarmed.
.
w
GB 43