Changing Batteries - Pentatech MA80 Mode D'emploi

Preparing for first use
Switching the panic alarm On / Off:
Press the PANIC key on the alarm unit or the
u
"PANIC" key on the remote control.
:
If the alarm is triggered, the word "TRIGGER" appears
at the bottom of the LC display
w
The siren sounds for 30 seconds (if the siren is
p
switched on – see section "Switching the siren on / off")
and the programmed telephone numbers are called
(if the automatic dialling function is switched on –
see section "Switching automatic dialling on / off).
After 30 seconds the siren sounds for a second
time for 30 seconds.
To stop the alarm and dialling process, enter your
current password and press the OK key
the key on the remote control.
d
The flashing word "TRIGGER" disappears.
The alarm unit sounds a pip and the alarm is now
switched off.
Note: Whilst the alarm unit is dialling a telephone number,
i.e. it is establishing a telephone connection, the panic
alarm cannot be disarmed using the keys on the device.
The remote control can be used to disarm the device at
any time.
Advice on the use of the panic alarm
The range of the remote control radio signals depends
on the construction of the building. Test the func-
tioning of the remote control from different locations
in the house. Take note of the locations from which
the remote control functions reliably. This should
give you an accurate picture of the effective operat-
ing radius of the remote control. you can alter the
position of the MA80, if necessary by the use of a
telephone extension cable.
Carry out an alarm test with all the people on the
call list and instruct them about what they should
do if they receive an "emergency" call.
44 GB
Please appreciate that during the dialling process
the telephone line will be engaged. To use your tel-
ephone or answer an incoming call you must press
the "0" button on the remote control to end the dial-
. ling process.
Switching the gong function on/off:
Set the gong On / Off switch
The gong sound sounds once.
After approx. 50 seconds delay a pip sounds. The
gong function is now activated.
If the motion detector
LED
or press sound sounds 2 x.
y
To switch the gong function off again, set the gong
On / Off switch
Note: In the armed state the gong function is not activated.
Summary of the last 5 alarm events:
This function is not available when in the setting mode nor
when the alarm and emergency telephone dialler is armed.
Press the
The times of the last 5 alarm events are displayed
one after the other.
Wait approx. 10 seconds and the display mode auto-
matically switches off again.
Summary of the stored telephone numbers:
This function is not available when in the setting mode
nor when the alarm and emergency telephone dialler is
armed.
Press the
The stored telephone numbers are displayed one
after the other.
Unassigned memory locations are shown as
"- - - - - - - - - - - - - -".
Wait approx. 10 seconds and the display mode
auto matically switches off again.
on (setting "I").
]
detects some motion, the
{
illuminates once more and the gong
q
off (setting "0").
]
key repeatedly.
i
key repeatedly.
o
Summary of the sounds
Sound Meaning
Three pips The exit delay is activated, the arming
of the alarm and emergency telephone
dialler will be activated after approx 55
seconds.
Single beep End of the exit delay
Siren alarm The siren sounds
1. Triggered by motion detection –
after the set entry delay in the cycle:
30 sec. on – 30 sec. pause –
30 sec. on.
2. Triggered by pressing the "PANIC"
key or as a panic alarm.
u :
Single gong Gong switch was set to setting "I", the
sound gong function is still not activated.
Two gong Motion was detected,
sounds the gong function is activated.

Changing batteries

Alarm unit
If the LED illuminates once every three seconds
q
(from approx 7.7 V + - 0.5 V), then you should renew the
9 V block battery. Replace the battery as described in
section "Power supply" under "Alarm unit - 9 V block
battery". In the armed state the alarm unit is supplied
with power for approx. 24 hours after the
starts to illuminate.
LED
q