Using The App - Pentatech AC50 Mode D'emploi

section. Note your password and keep in a safe place. If you forget your
password then reset the camera (chapter 1 ).
Event notify: (for iOS – for Android see chapter 10.1, where this
#
function is described) Select message upon motion detection (disable:
no message, Enable: send message)
Time Zone: Select the time zone for the camera location (GMT: UTC,
#
default = mid-european time: UTC(GMT)+01:00). To activate the
automatic summertime / wintertime tick "Daylight saving" during
summertime and remove the tick during wintertime.
Device Password: The security code for connecting to the camera can be
#
changed here. Select "Modify", enter the existing password and then
the new password twice. Confirm by tapping „OK" (default password:
123456)
Notes:
without the Device Password it is not possible to connect to the
#
camera. Note your password and keep in a safe place. If you forget
your password then reset the camera (chapter 13).
To reconnect the camera enter the new password into the System
#
Information.
Video Setting: Select by „
#
(faster frame rate but lower resolution) or „Better Image" (higher
r e s o l u t i o n , s l o w e r f r a m e r a t e ) . S e l e c t u n d e r
„Environment/Environment Mode"
camera location. For indoor use select „Indoor" (mains power
frequency 50 Hz for Europe, 60 Hz for USA) and for outdoor use
„Outdoor".
* WiFi Setting: To use the camera with WiFi connection to the WiFi
#
router without network cable connection, , select "Manage WiFi
network", select the WLAN router required and enter the password of
the router before disconnecting the network cable. After disconnecting
the network cable there will be a few minutes delay until the the WiFi
connection between the camera and WiFi router is established and the
green connection LED [5] illuminates. Resart the App.
Sensitivity Setting/Sensitivity:
#
„Low" for low sensitivity or „High" for higher sensitivity of the motion
detection (see chapter 12).
Email Setting/Email: Select "Set Email", enter the necessary data for
#
the Email address and confirm with "OK". An Email will be sent when
motion is detected. To activate, the field „Enable Email Alert" must be
ticked.
* SD Card Setting:
#
formatted. Note that formatting deletes all stored data on the card.
Select "Format SDCard" and confirm with "OK". To activate the ring
storage function (when the card is full the oldest data will be
overwritten), enter a tick by "Overwrite SDCard".
Update device firmware:
#
www.indexa.de store this onto the microSD card from the camera.
When using LAN connection (camera is connected via network cable
witjh the WiFi router) select "Update firmware" and the camera will
automatically reboot.
Device Information: Here you can find information about the camera
#
and the storage capacity of the microSD card.
28 - GB
3
Video Quality" between „Better Streaming"
the lighting environment for the
Select „Off" for no automatic recording,
After inserting a micro SD card it must be
Any new software will be available under
Tap on „Back" to return to System Information.
!
To save the settings tap „Save" [48] and confirm with „Yes" or „OK".
!
Note that after storage it can take a few minutes for the data to be updated.

10. Using the App

Notes:
Ensure that the camera is connected to the WiFi router – the green
#
connection LED [5] indicates connection.
When using WiFi connection the further the distance between camera and
#
WiFi router the slower the picture transmission.
In order to connect with the camera via internet, the WiFi router must be
#
connected to the internet.
For a local WiFi connection from the smartphone / tablet a connection of
#
the WiFi router with the internet is not necessary.
A successful App connection is indicated by a flashing green connection
#
LED [5].
Up to three users can access the camera concurrently.
#
The delay and the picture rate in the transmission is dependent on the
#
quality of the connections.
As with all tablets / smartphones, considerable costs can arise from
internet connection. A suitable flat rate contract is recommended.
10.1 Main side (see fig. D)
Open the „OMGuard" App. In the top left corner the word „Connected"
!
[21] will soon appear and the last viewed image from the previous session
(NOT live image) is shown [25]. If the App is not able to connect with the
camera „Disconnected" will be shown. In this case tap „update" [28] to
refresh the camera connection.
Note:
If the device password has been changed, „Wrong Password" will be
displayed. In this case tap „Operation" [27] followed by „Settings" [22]
and enter the valid password in the „Password" [43] field, confirm with
„Save" [48] and „Yes" or „OK".
Add camera
Tap „Add Camera" [26] to enroll a new camera, maximum 6 cameras per
!
smartphone / tablet. Proceed as per chapter 8.
Refresh the connection
Tap „Update" [28] to refresh the camera connection.
!
Activate PIN / Message upon motion detection / Information
Tap „information" [29].
!
You can activate the PIN code access after turning on the smartphone /
!
tablet as follows:
Tap „Setup PIN Lock".
!
Enter the chosen PIN two times and a tick by "Enable lock when
!
starting".
Note: without the valid PIN it is not possible to connect to the camera after
switching on your mobile device. Note your password and keep in a safe
place. If you forget the password the App must be deleted and then
reinstalled and the required cameras set up fresh.
In order to send a message through the App, to mobile devices which are
!