Korg PA 600 Guide De L'utilisateur page 417

88: Comp - Phaser
(Compressor - Phaser)
This effect combines a mono compressor and a phaser. You can
change the order of the effects.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
Compressor
EQ Trim LEQ HEQ
+
Comp
Output Level
Right
Envelope - Control
COMPRESSOR
[C]
a 1...100
Sensitivity
[C]Attack 1...100
b
Output Level 0...100
c [C]EQ Trim 0...100
[C]Pre LEQ
–15...+15
Gain [dB]
d
Pre HEQ Gain
–15...+15
[dB]
PHASER
[P]LFO
Frequency [Hz] 0.02...20.00
e
LFO Waveform Triangle, Sine
[P]Manual 0...100
f Depth 0...100
Resonance –100...+100
-Wet, -
[P]Phaser Wet/
1:99...Dry...99:1
Dry
, Wet
g
Src Off...Tempo
Amt –100...+100
h [F]Output Normal,
Mode Wet Invert
Comp Phaser,
i Routing
Phaser Comp
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src Off...Tempo
Amt –100...+100
FX Amt
Routing
Phaser
Phaser
Normal
+
Output Mode
–
Wet Invert
Resonance
Phaser FX Amt
FX Amt
LFO: Tri / Sine
Sets the sensitivity
Sets the attack level
Sets the compressor output level
Sets the EQ input level
Sets the gain of Low EQ
Sets the gain of High EQ
Sets the speed of the LFO
Selects the LFO Waveform
Sets the frequency to which the
effect is applied
Sets the depth of LFO modulation
Sets the resonance amount
Sets the phaser effect balance
Selects the Wet/Dry modulation
source for the phaser
Sets the Wet/Dry modulation
amount for the phaser
Selects the phaser output mode
Switches the order of the
compressor and phaser
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
89: Comp - Mt. Delay
(Compressor - Multitap Delay)
This effect combines a mono compressor and a multitap delay.
You can change the order of the effects.
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Left
Compressor
EQ Trim LEQ HEQ
+
Comp
Output Level
Right
Envelope - Control
COMPRESSOR
[C]
a 1...100
Sensitivity
[C]Attack 1...100
b
Output Level 0...100
c [C]EQ Trim 0...100
[C]Pre LEQ
–15...+15
Gain [dB]
d
Pre HEQ Gain
–15...+15
[dB]
MULTITAP DELAY
[D]Tap1 Time
0.0...1360.0
[msec]
e
Tap1 Level 0...100
[D]Tap2 Time
0.0...1360.0
[msec]
f
Feedback
–100...+100
(Tap2)
g [D]High Damp
0...100
[%]
Dry,
[D]Mt.Delay
1 : 99...99 : 1,
Wet/Dry
Wet
h
Src Off...Tempo
Amt –100...+100
Comp
Mt.Delay,
i Routing
Mt.Delay
Comp
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src Off...Tempo
Amt –100...+100
Page 406
Routing FX Amt
Multitap Delay
Feedback
Delay
(2)
(1)
High Damp
Mt.Dly FX Amt
FX Amt
Sets the sensitivity
Sets the attack level
Sets the compressor output level
Sets the EQ input level
Sets the gain of Low EQ
Sets the gain of High EQ
Sets the Tap1 delay time
Sets the Tap1 output level
Sets the Tap2 delay time
Sets the Tap2 feedback amount
Sets the damping amount in the
high range
Sets the multitap delay effect
balance
Selects the Wet/Dry modulation
source for the multitap delay
Sets the Wet/Dry modulation
amount for the multitap delay
Switches the order of the
compressor and multitap delay
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source