Korg PA 600 Guide De L'utilisateur page 409

70: Tape Echo BPM
This is a tape echo that lets you synchronize the delay time to the
tempo of the song.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
Feedback
Feedback Amt
Tape
+
Saturation
Trim Pre Tone
Right
BPM
Tempo
Base Note x Times
BPM
D -mod
MIDI,
BPM (Delay) 40.00...
300.00
a
Tap1 Dmod Src Off...Tempo
Tap1 Delay
r...w
Note
b Times x1...x32
Time Over? ---, OVER!
Tap1 Dmod
r...w
Note
c
Times x1...x32
Tap2 Position
d 0...100
[%]
Tap3 Position
e 0...100
[%]
Tap1 Level 0...100
f Pan L, 1...99, R
FB Amt –100...+100
Tap2 Level 0...100
g Pan L, 1...99, R
FB Amt –100...+100
Tap3 Level 0...100
h Pan L, 1...99, R
FB Amt –100...+100
Feedback 0...100
i Src Off...Tempo
Amt –100...+100
High Damp [%] 0...100
j
Low Damp [%] 0...100
k Saturation 0...100
Input Trim 0...100
l
Pre Tone 0...100
Wow Flutter
0.02...1.00
[Hz]
m
Wow Flutter
0...100
depth
Dry, 1:99...99:1,
Wet/Dry
Wet
n
Src Off...Tempo
Amt –100...+100
FX Amt
(3)
(2)
(1)
Level Pan
Delay
High / Low Damp
Wah Flatter Tap2/3 Position
FX Amt
Delay Time
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Selects the modulation source of
the delay time
Selects the type of notes to specify
the delay time (tap1)
Sets the number of notes to specify
the delay time (tap1)
Displays an error message when the
delay time exceeds the upper limit
Selects the note value used to
specify the delay time when the
modulation is at maximum
Specifies the number of notes used
to specify the delay time when the
modulation is at maximum
Sets the position of Tap 2 relative to
the Tap 1 delay time the depth of
pitch variation
Sets the position of Tap 3 relative to
the Tap 1 delay time the depth of
pitch variation
Sets the Tap1 output level
Sets the stereo image of tap1
Sets the Tap1 feedback amount
Sets the Tap2 output level
Sets the stereo image of tap2
Sets the Tap2 feedback amount
Sets the Tap3 output level
Sets the stereo image of tap3
Sets the Tap3 feedback amount
Sets the amount of feedback for
Taps 1, 2, and 3
Selects the modulation source of
feedback amount
Sets the depth by which feedback
amount will be modulated
Sets the damping amount in the
high range
Sets the damping amount in the low
range
Sets the distortion amount
Sets the input gain
Sets the tone of the input
Sets the frequency at which pitch
variation will occur
Sets the depth of pitch variation
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
a: Tap1 Dmod Src
b: Tap1 Delay Note
b: Times
c: Tap1 Dmod Note
c: Times
If "Tap1 Dmod Src" is Off or the selected modulation is at 0, the
delay time will be the length specified by "Tap1 Delay Note" and
"Times. "
If "Tap1 Dmod Src" is other than Off, the delay time will change
so that it will be as specified by "Tap1 Dmod Note" and "Times"
when the maximum modulation is reached.
b: Time Over?
You can set the delay time up to 5,400msec. If the delay time
exceeds this limit, the error message "OVER!" appears in the dis-
play. Set the delay time parameters so that this message will not
appear. "Time Over?" is only a display parameter.
Page 398