Using The Accessories; Maintenance - shark EP780C Manuel Du Propriétaire

Using the Accessories

Fig. 7 Fig. 8
Using the Combo Crevice/Dusting Using the Turbo Brush:
Tool:
The Turbo Brush can be attached to
The Combo Crevice/Dusting tool either one or both extension tubes
can be attached to either one or for greater reach or directly onto
both extension tubes for greater the handle.
reach or directly onto the handle.
1 Remove the floor brush from
1 Remove the floor brush from the lower extension tube and
the lower extension tube and then depending on the length
then depending on the length that you desire, just push it in to
that you desire, just push it in to the end of the extension tube or
the end of the extension tube or the handle. (Fig. 8)
the handle. (Fig. 7)
Note: The efficiency of your Turbo
Brush depends on the bristle brush
rotating at high speed. Strong air
action is needed to accomplish this.
In order to ensure that maximum air
suction is maintained:
a Change the dust bag
frequently.
b Replace the filter as needed.
c Ensure that the rotating
brush is kept free of hair and
debris which may accumulate
and decrease brush
performance.
6 TOLL FREE: 1-800-798-7398

Maintenance

Fig. 10
Fig. 9
Cleaning the Turbo Brush:
From time to time, the turbine
of your turbo brush will require
Fig. 11
cleaning.
1 Remove the Turbo Brush from
Dust Bag Full Indicator:
the hose or extension tube.
The red dust bag full indicator may
2 Turn the Turbo Brush over and
turn on while you are vacuuming to
open the hinged cover to access
indicate that the dust bag is full and
the turbine wheel. (Fig. 9)
needs to be replaced.
3 There may be dust, lint, hair, etc
Replacing the Dust Bag:
on the turbine wheel. Remove
as much of this as possible. Use 1 P ress the On/Off Button to the
the vacuum with the hose to
remove any additional debris
2 R emove the flexible hose from
that may remain.
3 P lace your fingers underneath
4 H old the cardboard collar of the
CAUTION:
To reduce the risk of shock, the
power cord must be disconnected
before removing or inserting the
dust bag.
Fig. 12
Fig. 13
5 H olding the cardboard collar,
insert a new dust bag into
the slots of the dust bag
compartment. (Fig. 13)
6 C lose the top cover of the
vacuum.
Cleaning the Pre-Motor Filter:
"Off" position. 1 P ress the On/Off Button to the
"Off" position.
the vacuum by squeezing the 2 O pen the top cover and pull the
locking tabs on the neck of the pre-motor filter straight out.
(Fig. 14)
hose and pulling it out. (Fig. 10)
3 W ash the filter in lukewarm
the opening indentation behind
water and allow to air dry
the vacuum handle and lift the completely for 24 hours.
top cover up. (Fig. 11)
4 S lide a dry pre-motor into
position between the two posts
dust bag and gently pull the and the motor intake.
dust bag out. (Fig. 12)
English
Fig. 14
To Reset the Motor Thermostat:
Your Shark Quick Clean Canister
®
vacuum is equipped with a protective
Motor Thermostat. If the motor
should overheat, the thermostat
shuts off the power.
1 P ress the Power Button to turn
the unit "Off".
2 U nplug the vacuum.
3 C heck for clogged hose or filter;
unclog hose and replace filter.
4 W ait 45 minutes for vacuum to
cool; then plug in the vacuum.
5 P ress the Power Switch to start
the vacuum.
Note: If vacuum still does not start,
contact Customer Service at:
1-800-798-7398.
www.sharkclean.com 7