Scheppach 5904605903 Manuel D'instruction page 16

Hand Grip
When operating the compactor, use this hand
grip to maneuver the compactor.
Shift Stick
Push the stick forward, the compactor will
move in a forward direction. Pull the stick
backwards, the compactor will move in
reverse direction. Placing the stick in the
middle will cause the compactor not to move
(neutral).
Throttle Control
The throttle lever controls engine speed.
Moving the throttle lever in the directions
shown makes the engine run faster or slower.
Handlebar
When operating the compactor, this handle
■ENGINE COMPONENTS (FIG. 2)
1 Spark plug
2 Muffler
3 Choke lever
4 Fuel tank cover
5 Fuel tank
6 Throttle control assy.
■ CHECK BEFORE OPERATION
1) Check
• Look around and underneath the engine
GB for signs of oil or gasoline leaks.
2) Check Oil
1) Take the oil dipstick and clean
2) Insert the oil dipstick in and check the oil lever without screwing down.
3) If the oil is too low, add the recommenced oil in.
4) After finishing, reassemble and screw the oil dipstick down.
3) Check fuel
First stop the engine, open the fuel cover, and
check oil level., if the oil level is too low, add
the fuel to full, after finishing, screw the fuel
cover down.
Don't add the fuel over the shoulder of the
■ STARTING ENGINE
1. Move the fuel valve lever to the ON position
To start a cold engine, move the choke to
the CLOSE position.
2. To restart a warm engine, leave the choke
■ RECOIL STARTER
Pull the starter grip lightly until you feel
resistance, then pull briskly, return the starter
grip gently. If the choke lever has been moved
to the CLOSE position to start the engine,
■ FORWARD AND REVERSE MOTION, FIG. 3
The direction of travel is determined with
the operating control shifter. Depending on
the position of the control shifter, the plate
compacts in forward direction, on the spot or
in reverse direction.
1. To make the compactor move in the
forward direction, push the shift stick
Commissioning
is to be in the downward position. When the
compactor is to be stored, move the handlebar
to the upright position.
Lift Point
Used to lift the machine with crane or other
lifting device.
Belt Guard
Remove this guard to gain access to the
V-belt. Never run the compactor without
the V-belt guard. If the V-belt guard is not
installed, the possibility exists that your hand
may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
Exciter
An eccentric weight mounted on the exciter
shaft contained within exciter housing is
Controls / Compactor Operations (Fig. 2)
7 Starting lever
8 Recoil starter
9 Air cleaner
10 Oil dipstick
11 Drain plug
12 Switch
• Look for signs of damage.
• Check that all shields and covers are in
carburetor when fueling (maximum oil level).
Recommended octane rating over 90 unlea-
ded gasoline
For unleaded gasoline, can make carbon de-
posit muck less and enhance exhaust system
lever in the OPEN position.
3. Move the throttle lever away from the
SLOW position, about 1/3 of the way toward
the FAST position.
gradually move it to the OPEN position as the
engine warms up. After engine warms up, pull
throttle lever to accelerate engine speed and
place the shift stick at the desired position.
forward.
2. If shift stick is placed in the neutral position,
the compactor will vibrate on the spot.
3. To make the compactor move in the
reverse direction, pull the shift stick
backwards.
m Do not operate plate on concrete or on
driven at high speed by a clutch and belt
drive system. This high speed shaft revolution
causes the rapid lifting and downward
ramming motion of the machine as well as
imparting a forward motion.
Engine switch
The engine switch enables and disables the
ignition system. The engine switch must be in
the ON position for the engine to run.
Turning the engine switch to the OFF position
stops the engine.
Running the engine with dirty oil can cause
premature engine wear and failure. Changing
oil regularly is extremely important.
13
14
15 Fuel valve
service life
Don't use used and contaminated or gasoline
with oil , Avoid the dirt and water entering
into fuel tank.
4. Place the shift stick in the neutral position.
5. Turn the engine switch to the ON position.
6. Operate the starter.
Plate will begin vibrating and proceed with
compacting.
The number of passes required to reach a
desired compaction level will depend on the
type and moisture content of soil. Maximum
16
Ventilation screw
Oil dipstick
place, and all nuts, bolts, and screws are
.
tightened.
extremely hard, dry, compacted sur-
faces. The plate will jump rather than
vibrate and could damage both plate
and engine.