Table des Matières
Publicité
GB
Any interference with parts of the product that are not descri-
■
bed within the manual may cause damage, or endanger the
person using this machine. Extensive repairs must only be car-
ried out by KETTLER service staff or qualified personnel trained
by KETTLER.
In case of enquiry, please contact your KETTLER dealer.
■
Handling the equipment
Before using the equipment for exercise, check carefully to en-
■
sure that it has been correctly assembled.
Do not set the equipment up in rooms which are frequently used
■
or close to doors, entries etc.
It is not recommended to use or store the apparatus in a damp
■
room as this may cause it to rust. Please ensure that no part of
the machine comes in contact with liquids (drinks, perspiration
etc.). This may cause corrosion.
The machine is designed for use by adults and children should
■
not be allowed to play with it. Children at play behave unpre-
dictably and dangerous situations may occur for which the ma-
nufacturer cannot be held liable. If, in spite of this, children are
allowed to use the equipment, ensure that they are instructed in
its proper use and supervised accordingly.
The exercise cycle complies with the DIN EN 957 - 1/8, class
■
H (Homesport). It is therefore unsuitable for therapeutic use.
The "Power Stepper" must be set up on an even impact-resistant
■
base. To absorb the vibrations, lay a straw or rubber mat un-
der the machine.
Do not use corrosive or abrasive materials to clean the equip-
■
ment. Ensure that such materials are not allowed to pollute the
Instructions for Assembly
Ensure that you have received all the parts required (see check
■
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
Before assembling the equipment, study the drawings carefully
■
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
The equipment must be assembled with due care by an adult
■
person. If in doubt call upon the help of a second person, if
possible technically talented.
Please note that there is always a danger of injury when wor-
■
king with tools or doing manual work. Therefore please be ca-
reful when assembling this machine.
Ensure that your working area is free of possible sources of
■
danger, for example don't leave any tools lying around. Al-
ways dispose packaging material in such a way that it may not
List of spare parts
When ordering spare parts, always state the full article number,
spare-partnumber, the quantity required and the S/N of the pro-
duct (see handling).
Example order: Art. no. 07877-000 / spare-part no.
70132297/ 2 pieces / S/N .................... Please keep original
packaging of this article, so that it may be used for transport at
a later date, if necessary.
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this
4
In choosing the location of the apparatus, ensure a sufficient sa-
■
fety distance from any obstacles. The apparatus must not be
mounted in the immediate vicinity of main passageways (paths,
doorways, corridors).
The product is not suitable for use by persons weighing over
■
110 kg.
environment.
After a longer period of disuse, the hydraulic absorbers may
■
not achieve their best performance at once. Before beginning
exercising or after a period of disuse, it is recommended to ac-
tivate the absorbers by several pumping movements.
To operate correctly, the pulse function requires a minimum vol-
■
tage of 2,7 volts (only for computers working with batteries).
Please ensure that liquids or perspiration never enter the ma-
■
chine or the electronics.
Before use, always check all screws and plug-in connections as
■
well as respective safety devices fit correctly.
Always wear suitable shoes when using.
■
All electric appliances emit electromagnetic radiation when in
■
operation. Please do not leave especially radiation-intensive
appliances (e.g. mobile telephones) directly next to the cockpit
or the electronic controlsystem as otherwise values displayed
might be distorted (e.g. pulse measurement).
When training intensivly shock absorbers may become very
■
hot. Please avoid contact and do not touch the shock absorbers
after training.
cause any danger. There is always a risk of suffocation if child-
ren play with plastic bags!
The fastening material required for each assembly step is sho-
■
wn in the diagram inset. Use the fastening material exactly as
instructed. The required tools are supplied with the equipment.
Bolt all the parts together loosely at first, and check that they
■
have been assembled correctly. Tighten the locknuts by hand
until resistance is felt, then use spanner to finally tighten nuts
completely against resistance (locking device). Then check that
all screw connections have been tightened firmly. Attention:
once locknuts have been unscrewed they no longer function
correctly (the locking device is destroyed), and must be repla-
ced.
For technical reasons, we reserve the right to carry out preli-
■
minary assembly work (e.g. addition of tubing plugs).
should be clearly stated on the order by adding the words „with
fastening material".
KETTLER (GB) Ltd.
GB
Merse Road · North Moons Moat · Redditch, Worcesters-
hire B98 9HL · Great Britain
http://www.kettler.co.uk
KETTLER International Inc.
USA
P. B. 2747 · Virginia Beach, VA 23450-2747
http://www.kettlerusa.com
Publicité
Table des Matières
