Personnel Qualifications; Delivery Contents; About This Product; Product Description - Aventics RV2 Mode D'emploi

AVENTICS | RV2 | R412020036–BDL–001–AB | English
O
Permissible media are exclusively non-toxic, neutral, and non-
flammable gases and vapors that can be discharged via a
restricted exhaust. Water vapor, media that contain particles,
or liquid or adhesive media are not permissible. Use of
inadmissible media can lead to hazards for the operator and
the safety valve.
O
Use is permitted only under the operating conditions and
within the performance limits listed in the technical data.
O
The safety valve is only intended for industrial applications.
Intended use includes having completely read these instructions,
especially the section "Notes on Safety".
Improper use
O
Use as an overflow device, control valve, or drain valve under
constant operation is not permissible. This can cause
mechanical damage to the valve seat (e.g. due to the sealing
cone digging into the gasket), so that the response tolerance
can no longer be maintained.
O
Permanent blow-off is not permissible as this can cause
vibration. This could also lead to mechanical damage.

Personnel qualifications

All tasks associated with the products require basic mechanical,
pneumatic and electrical knowledge, as well as knowledge of the
respective technical terms. In order to ensure operational safety,
these tasks may only be carried out by qualified personnel or an
instructed person under the direction of qualified personnel.
Qualified personnel are those who can recognize possible hazards
and institute the appropriate safety measures, due to their
professional training, knowledge, and experience, as well as their
understanding of the relevant conditions pertaining to the work to
be done. Qualified personnel must observe the rules relevant to the
subject area.
General safety instructions
W Observe the valid local regulations to protect the environment
in the country of use and to avoid workplace accidents.
W The warranty will not apply if the product is incorrectly
assembled.
W The manufacturer can accept no liability claims if these
instructions are not complied with; the warranty for appliances
and accessory parts will no longer apply.
W Any disassembly of the safety valve is prohibited.
W The safety valve is sealed according to Directive 97/23/EC, and
is therefore secured against readjustment. It is not possible to
make readjustments in the venting screw without damaging
the sealing cap. Loosening or damaging the sealing cap
terminates liability.
W Mechanical changes, such as opening the safety valve or
changing the set pressure, can only be implemented in the
manufacturer's facility or by authorized institutions.
W Do not place any deflection, torsion, or impact loads on the
safety valve.
W Only use AVENTICS products that are in perfect working order.
W Examine the product for obvious defects, such as cracks in the
housing or missing screws, caps, or seals.
W Do not modify or convert the product.
W Product warnings and information must be legible, i.e. not
covered by paint, etc.
Safety instructions related to the product
and technology
W Due to the often large discharge amounts, install the safety
valve with restricted exhaust at a point where no personnel can
be injured. In addition, make sure that there is sufficient blow-
off area (approx. twice as large as the nominal size) so that no
other equipment is damaged.
W The safety valve must be accessible for maintenance work and
must not protrude into traffic areas.
W It is not permitted to connect any other fittings, e.g. filters or
shock absorbers, to safety valves with restricted exhaust.
W The working pressure must be at least 5% lower than the
closing pressure or at least 15% lower than the set pressure of
the safety valve.
W Select a safety valve such that the discharge amount is larger
than the injection flow of the supply line or the compressor.
W If the safety valve is exposed to weather, implement
appropriate measures to protect it from snow, ice, and solid
particles. For example, roofing that does not impede the
exhaust.
W Only qualified personnel may perform assembly and
maintenance (see "Personnel qualifications").
W Use the safety valve only for the intended application (see
"Intended use") and only under conditions specified in the
technical data and within the stipulated limits. Non-compliance
can lead to severe injury or even death.
3

Delivery contents

W 1x safety valve
4

About This Product

Product description

If overpressure is generated in a pressure tank or in piping, the
safety valve discharges the operating medium until the desired
working pressure is re-established.
Product identification
TUV. SV. xx- xxxx.
TÜV symbol
Safety valve
Year of component test
Test number
Narrowest flow diameter
1)
Code letters
Assigned exhaust number
Set pressure [bar]
1)
D/G: intended for vapors/gases
5 Assembly
Danger of injury if assembled under pressure!
Assembling when under pressure can lead to injuries and
damage to the product or system components.
O
Make sure that the relevant system part is not under
pressure before you assemble the product.
O
Protect the system against being switched on.
W Operating instructions
–
type code
xx. D/G. 0,xx.
CAUTION
4
xx