Function Modes - Cardin Elettronica GL 24Vdc Motors 310/GLB249M Manuel D'installation

REMOTE CONTROL (fig. 6, 7 - pages 7, 8)
The system can be remotely activated using radio control devices; to set
the two functions to channels A-B-C-D use the selection jumper "J2":
- position "1" function 1 selected, SEQUENTIAL COMMAND;
- position "2" function 2 selected, CH2 (binding posts 31,32).
The sequential command may be set (dip "1") to "open-block-close-
block" or "open-close".
Memory module (MM)
This is extractable, furnished with a non volatile EEPROM type memory
and contains the transmitter codes and allows you to memorise up to
300 codes. The programmed codes are maintained in this module even
during blackouts.
Note: Before memorising the transmitters for the first time
remember to cancel the entire memory content. If the electronic
card has to be replaced due to failure, the module can be
extracted from it and inserted into the new card. Make sure that
the module is correctly inserted as shown on pages 7, 8.
Signal LEDs "L4" (pages 7, 8):
Flashing quickly: cancels a single code
Flashing slowly: memorises a single code
Permanently lit: memory full.
TRANSMITTER CODE MANAGEMENT
Memorising a channel (pages 7, 8):
1) Press and hold down button "P3" MEMO: The LED "L4" will flash
slowly.
2) At the same time activate the transmitter which is to be memorised.
3) Hold down button "P3" MEMO until LED "L4" starts to flash again.
4) Release the "P3" MEMO button: The LED will continue to flash.
5) Activate the transmitter again (same transmitter, same channel; if the
channel is different or it is a different transmitter the memorisation
attempt will abort without success).
6) End of memorisation: the LED "L4" will remain lit for 2 seconds, indicat-
ing that the transmitter has been correctly memorised.
Note: It is not possible to memorise a code which is already in memory: if
you attempt this, the LED will switch off when you activate the transmitter
(point 2). Only after releasing the button "P3" MEMO will you be able to
continue the memorising procedure. If after activating the transmitter for
the first time you wait for more than fifteen seconds without activating the
transmitter a second time the memorisation attempt will abort without
success.
Cancelling a channel (pages 7, 8):
1. Press and hold down the button "P2" DEL: the LED "L4" will flash
quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LED will remain lit for 2 seconds indicating that the transmitter has
been cancelled.
Note: If the user that you wish to cancel is not in memory, the LED will stop
flashing; only after releasing the button "P2" will you be able to continue
the cancellation procedure.
For both the memorisation and cancellation procedures, if the button is
released before activating the transmitter the procedure will abort.
C) Cancelling all user codes from memory (pages 7, 8):
1) Keep both buttons pressed down ("P2+P3") for more than four sec-
onds.
2) LED "L4" will remain lit during the entire cancellation time (about 8
seconds).
3) LED "L4" switches off when the cancellation procedure has termi-
nated.
Note: When the memory is almost full the time required to search for a user
code could take up to 1 second from when the command was received. If
led "L4" remains lit memory is completely full.
To memorise a new transmitter you will first have to cancel a code from
memory.
D) Memorising ulterior channels via radio
• Memorisation can be activated by radio (without opening the receiver
container) if jumper "J1" has been inserted (pages 7, 8).
1) Make sure that the jumper "J1" has been inserted (pages 7, 8).
2) Using a transmitter, in which at least one
channel button "A, B, C or D" has already
been memorised in the receiver, press
the button in the transmitter as shown in
figure.
Note: all the receivers within range when the channel button is
pressed (and which have at least one of the transmitter channel but-
tons memorised) will activate their signal buzzer "B1" (pages 7, 8).
3) Press one of the channel buttons on the same transmitter. The receivers
which do not contain that channel code will sound a five-second long
"beep" and will then deactivate.
The receivers which contain the channel code will sound a one-second
long "beep" and will enter the "programming via radio" mode.
4) Press the previously chosen channel buttons on the transmitter which
you wish to memorise; the receiver will sound 2 "beeps" of half a second
each after which the receiver will be ready to receive another code.
5) To leave the programming mode wait for 3 seconds without pressing
any buttons.
The receiver will sound a five-second long "beep" and will then exit the
programming mode.
Note: When the memory is entirely occupied the buzzer will sound 10 rapid
"beeps" and will automatically leave the "programming via radio" mode.
Led "L4" will remain lit on the receiver.
The same signal is given each time you try to enter "programming via
radio" when the memory is full.
CONNECTING THE ANTENNA
Connect an ANS400 tuned antenna using a coaxial cable RG58 (imped-
ance 50Ω) with a maximum length of 15 m.

FUNCTION MODES

1) Automatic
This is selected by enabling automatic reclosing (dip "2" in position "ON").
Starting from the completely closed position the sequential command starts
a complete function cycle that terminates with automatic reclosing.
Automatic reclosing starts after the programmed pause period has elapsed
when the opening cycle has been completed or straight away after the
intervention of a photoelectric cell (the intervention of a photoelectric cell
causes the pause time to be reset).
During the pause time the symbol
the blocking button during this period will stop automatic reclosing and
consequently stop the display from flashing.
Note: the courtesy light switches on each time a movement command is
given (both via cable or via radio) and switches off 30 seconds after the
manoeuvre has been completed.
2) Semiautomatic
Selected by deactivating automatic reclosing (dip "2" in position "OFF").
Work cycle control using separate opening and closing commands.
When the door has reached the completely open position the system
will wait until it receives a closing command either via an external control
button or via radio control, before completing the cycle.
26
All rights reserved. Unauthorised copying or use of the information contained in this document is pun
Description : MEMORIZZAZIONE CODICE Tx-Rx
Drawing number : DM0531
Product Code : RCQ449100
Draft : P.J.Heath Date : 13-04-2001
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/4018
will flash on the display and pressing