Gardena 2000/2 Clear 18V P4A Mode D'emploi page 7

To connect the telescopic pipe (Art. 14602) [ Fig. A5 ]:
We recommend the use of a GARDENA Hose
Connector for connecting a garden hose:
– Art. 18215 for 13 mm (1/2") and 15 mm (5/8") or
– Art. 18216 for 19 mm (3/4"). With the use of
19-mm-(3/4")-hose line, the pumping quantity is
the greatest.
The telescopic pipe can be adjusted between 57 – 77 cm.
The telescopic pipe can be extended several times by
21 cm with the GARDENA Extension Pipe Art. 1420.
3. OPERATION
DANGER! Risk of injury!
Injury when the product starts accidentally.
v Remove the battery before you adjust or trans-
port the product.
To charge the battery [ Fig. O1 / O2 / O3 ]:
CAUTION!
v Note the mains voltage! The voltage of the power
source must match the voltage specified on the rating
plate of the charger.
Thanks to the intelligent charging process, the charge
condition of the battery is automatically detected and then
charged up with the optimal charge current depending
on battery temperature and voltage.
In this way, the battery is treated with care and remains
permanently fully charged when it is stored in the charger.
(8)
1. Open the cover .
2. Push the locking button
from the battery container
3. Connect the battery charger
4. Slide the battery charger
When the battery charge indicator
flashes green the battery is being charged.
When the battery charge indicator
illuminates permanently green the battery is com-
pletely charged
(Charging time, see 7. TECHNICAL DATA).
5. Examine the charge status regularly while you charge.
(B)
6. When the battery is completely charged, you can
disconnect the battery
Meaning of the Indication Elements:
Indication on the charger [ Fig. O3 ]:
Flashing of the The charging procedure is indicated by flashing
Battery Charge
of the battery charge indicator
(Lc)
Indicator
Note: The charging procedure is only possible
when the battery temperature is within the
allowable charging temperature range,
see 7. TECHNICAL DATA.
GAR_14600-56.960.02_2024-11-28.indb 7 GAR_14600-56.960.02_2024-11-28.indb 7
(A) (B)
and remove the battery
(D)
.
(C)
into a mains socket.
(C) (B)
onto the battery .
(Lc)
at the charger
(Lc)
at the charger
(B) (C)
from the charger .
(Lc)
.
1. Screw the telescopic pipe (3)
nector (1) . Make sure that the washer
connecting thread (5) of the telescopic pipe
2. Loosen the threaded collar
pipe (3) .
3. Adjust the telescopic pipe (3)
4. Tighten the threaded collar
(3) is fitted with a GARDENA Shut-Off
The telescopic pipe
Valve (7) (7)
. The shut-off valve
adjustment of the pump performance.
Continuous Continuous lighting of the battery charge
(Lc)
Lighting of the
indicator indicates that the battery is fully
Battery Charge charged or that the temperature of the battery
(Lc)
Indicator
is not within the allowable charging tempera-
ture range and can therefore not be charged.
When the battery is not inserted, continuous
lighting of the battery charge indicator
indicates that the mains plug is inserted in the
socket outlet and that the battery charger is
ready for operation.
Battery charge status indication on the product
[ Fig. O1 / O4 ]:
After starting the product, the battery charge status
indication [ (L1) , (L2) and (L3) ] is displayed.
Battery charge status Battery charge status
indication
(L1)
67 – 100 % charged
(L1)
34 – 66 % charged
11 – 33 % charged (L1)
0 – 10 % charged (L1)
(L1)
If the LED flashes green, the battery must be
charged.
If the error LED (Wp) is illuminated or flashing,
see 6. TROUBLESHOOTING.
Control panel [ Fig. O4 ]:
(s)
On / Off button :
v Push the On / Off button (s)
The pump starts with the previously selected power
level.
After the pump is switched on, the battery charge status
indication ( (L1) , (L2) , (L3) ) is displayed with green LEDs.
(m) Power levels (Flow button) / Timer Function:
The pump has 3 power levels, which can be called up
one after the other with the Flow button. To do this, the
Flow button must be pressed briefly (approx. 0.5 sec.).
According to the power level the LEDs (
blue for 5 seconds.
If the flow button is pressed for 3 seconds, the timer
function is activated.
onto the pump con-
(4) lies in the
(3) .
(6) of the telescopic
to the desired height.
(6)
again.
can also be used for fine
(Lc)
(L2) (L3)
, and illuminate green
(L2)
and illuminate green
illuminates green
flashes green
on the control panel.
(L1) (L2) (L3)
, , ) flash
7
28.11.24 12:36 28.11.24 12:36