Publicité
11
MAINTENANCE AND STORAGE
The unit features degree of protection IPX7 (fully waterproof, submersible at
1 meter for 30 minutes).
Attempts to disassemble or repair the scope will void the warranty!
Clean the scope's optical surfaces only if necessary, and use caution. First,
remove (by blowing with a blower brush or canned air) any dust or sand
particles. Then proceed to clean by using camera/lens cleaning equipment
approved for use with multicoated lenses. Do not pour the solution directly
onto the lens!
Always store the unit in its carrying case in a dry, well-ventilated space. For
prolonged storage, remove the batteries.
Batteries shall not be exposed to excessive heat such as sunshine, fire or the
like.
12
TROUBLESHOOTING
Listed below are some potential problems that may occur when using the
scope. Carry out the recommended checks and troubleshooting steps in the
order listed. Please note that the table does not list all of the possible
problems. If the problem experienced with the scope is not listed, or if the
suggested action meant to correct it does not resolve the problem, please
contact the manufacturer.
Problem
Possible cause
Batteries have been
The unit will not turn on.
incorrectly installed.
.
Battery cover is not tightly closed.
Oxidized contact points in the
battery compartment or
on the battery cover due to
"leaky" batteries or contact
points becoming exposed
to a chemically reactive solution.
The batteries are fully
exhausted or one or
several batteries are faulty.
The image is blurry, with
Calibration is to be done.
vertical stripes and uneven
background.
The image is too dark.
The lowest brightness level
is set.
Point of impact does not
Display calibration needs to be
match the aiming point.
done.
14
Corrective action
Reinstall the batteries
observing polarity.
Close tightly the battery cover.
Clean the contacts of the battery
compartment or the battery cover.
Install fresh batteries.
Do the calibration according
to section 9 "OPERATION"
Adjust display brightness.
Do display calibration as per
guidelines below.
Display calibration
Press simultaneously and hold for two seconds buttons "LEFT" (10) and "MODE"
(12) or RC buttons (23) and (24) to enter the auxiliary menu. Press buttons "LEFT"
(10) or "RIGHT"(11) to select menu item
to confirm.
Auxiliary cross in a limiting frame
and symbols will appear on the display
First, match the auxiliary cross and the centre of sight's reticle.
To move the frame with the cross horizontally and vertically, press buttons "LEFT" or
"RIGHT" (or RC buttons (22),(24)). Movement takes places upon both short and long
press. To switch movement direction from horizontal to vertical, press button "MODE"
or (23) RC button.
Second, hold "MODE" (or (23) RC button) for two seconds. Figure "2" and X, Y
coordinates values appear next to the icon
While holding the reticle in the aiming point, move the auxiliary cross to the point of
impact with buttons "LEFT" or "RIGHT" (or RC buttons (22),(24). To switch movement
direction from horizontal to vertical, press button "MODE" or (23) RC button.
Horizontal/vertical travel range of the auxiliary cross relative to the limiting frame is +/-
10.
Eventually the auxiliary cross should match the point of impact, with the sight's reticle
being held in the aiming point.
To save display calibration parameters, keep the "MODE" button (or (23) RC button)
pressed for two seconds - display will show "OK" message; the image of the target
centre should now coincide with the centre of the of sight's reticle.
To restore factory settings, select "Yes" in the item
Parameters as follows are restored to factory settings:
Operating mode – "Forest";
Brightness of menu symbols – 5;
Magnification – x1;
Brightness settings – 10;
Image calibration mode – automatic;
Display calibration – coordinates X=0, Y=0;
Color inversion - off;
Contrast settings – 6.
Note. Auxiliary menu items ("Display calibration" and "Default settings") are only
available when the unit is in attachment mode.
"Display calibration". Press "MODE"
1
.
.
"Default settings".
15
Publicité
