Electric Shock Hazard; Important Safety Information - Hatco Glo-Ray GRHW-2P Manuel D'installation Et D'utilisation

English
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
WARNING

ELECTRIC SHOCK HAZARD:

• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install the proper voltage
and size electrical receptacle.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any maintenance or
cleaning.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• Do not steam clean or use excessive water on unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged
power cord. The cord must be replaced by Hatco, an
Authorized Hatco Service Agent, or a person with
similar qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD: Locate unit a minimum of 1" (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
Make sure food product has been heated to the proper
food-safe temperature before placing on the unit. Failure
to heat food product properly may result in serious health
risks. This unit is for holding preheated food product only.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them
away from the unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
Form No. GRHWM-0520

IMPORTANT SAFETY INFORMATION

Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. The location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36" (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point
of use, 4" (102 mm) legs are included to allow for proper
cleaning access below unit.
Do not allow the glass shelf to overheat. Overheating may
cause the food containers to melt or soften.
Do not use food pans, ceramic dishes, or abrasive
materials on heated glass shelf. Scratching of the glass
surface may occur, marring its appearance and making it
susceptible to dirt accumulation. Damage to glass surface
or breakage of glass caused by misuse is not covered
under warranty.
Do not slide pans across hardcoat surface, use rough-
bottomed pans, or drop anything on hardcoat surface.
Scratching may occur. Damage to hardcoat surface caused
by misuse is not covered under warranty.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
Use non-abrasive cleaners only. Abrasive cleaners could
scratch the finish of the unit, marring its appearance and
making it susceptible to soil accumulation.
IMPORTANT—DO NOT use paper towel or glass cleaner
to clean polycarbonate surfaces. Paper towel and glass
cleaner may scratch the material. Wipe off polycarbonate
surfaces using a soft, clean, and damp cloth.
Do not drag or slide unit when moving or installing.
Carefully lift unit to prevent the rubber feet from tearing
off.
Locate the unit in an area where the ambient air temperature
is constant and a minimum of 70°F (21°C). Avoid areas that
may be subject to active air movements or currents (i.e.,
near exhaust fans/hoods and air conditioning ducts).
3
WARNING
CAUTION
NOTICE