Publicité
EN
INSTALLATION OF TANGENT STOP
The frame is also supplied with a tangent clamp for
the seat post, which should be tightened to a torque
NO.
of 7 Nm. Be sure not to exceed this torque to avoid
1
damaging your seat post and to prevent cracks
2
Top cap
around the frame housing.
3
expander
4
5
Stem cable guide
6
Head spacer
7
Head spacer
8
Headset cap
9
compress ring
10
Bearing
11
Front thru axle
12
13
Seatpost
14
Torx Screw
15
washer
16
Wedge Top part
17
Wedge low part
18
FD hanger
19
19-1
20
Rear thru Axle
21
Rear Hanger
22
Dropout
23
rubber cable guide
24
rubber cable guide
WARNING : The tangent clamp must be
!
mounted so that it does not slip into the seat
25
rubber cable guide
tube; no part of this collar should protrude
26
beyond the frame.
27
Speed sensor guide
28
rubber cable guide
29
rubber cable guide
IMPORTANT : You must ensure that the
minimum insertion of the seat post into the frame
30
SS Bridge
is respected, as indicated on the seat post itself.
31
rubber cable guide
32
rubber cable guide
33
Engine cover
34
35
36
37
38
39
Frame
40
41
Name
Spec.
Reference
Screw
M6*P1.0*L30mm
TK2863-1
TK2863
26896
Stem
5mm /
half
10mm /
half
New for E-765 use
Φ49.5*Φ40*6.5mm
M12*P1.5*L115mm
26332
Screw
M5*P0.8*12mm+Φ10*1mm
Φ27.2
M5*P0.8*20MM
Φ9.0*5.3*T1mm
AL 6061/T6
Screw
M4*P0.7*14mm
26663
Screw
M4*P0.7*14mm
26663
M12*P1.5*L160mm
26333
inside
26662
outside
26661
Rear, cover
for mechanical(Φ4.3)
for Di2(Φ2.8)
Screw
M4*P0.8*8mm
hold speed sensor
for speed sensor
cable (Φ2.8)
for FD cable routing
cable (Φ4.5)
for charge port
cable routing(Φ7)
cover, for charge port
cover, for charge port
Screw
M4*P0.8*12mm
Screw
M6*P1.0*12mm
Screw
M6*P1.0*18mm
M6*P1.0*23mm
Screw
L side
M6*P1.0*30mm
Screw
R side
Size : XS/S/M/L/XL
Fork
offset 50mm
Screw
M5*P0.8*10mm+Φ10*1mm
NOTE : For the complete installation of the LOOK headset, it is highly recommended to consult your
Torque
Qty
Unit
authorized LOOK dealer.
2Nm
1
pcs
1
pcs
8Nm
1
set
1 - Grease the upper seat of your frame and place a
1
set
bearing (13) on this seat.
1
pcs
2 - Grease the lower seat of your frame and fork,
4
pcs
then place a bearing (13) in the frame, ensuring
8
pcs
the outer chamfer faces inward toward the headset,
1
set
then slide your fork into the frame.
1
pcs
3 - Lightly grease the upper bearing seat and slide
2
pcs
the compression cup (12) onto the fork until it
11Nm
1
pcs
reaches the upper bearing.
4Nm
4
set
1
pcs
4 - Slide the junction spacer (10) with its seal (11)
7Nm
1
pcs
onto the fork, then slide it down to the compression
1
pcs
cup (12).
1
pcs
5 - Slide the desired spacers (8) of 5 mm or (9) of 10
1
pcs
mm with the cables placed inside, without exceeding
1
pcs
a maximum of 50 mm.
3Nm
1
pcs
3Nm
2
pcs
6 - Slide the specific stem cable guide (7) with the
11Nm
1
pcs
cables placed inside.
1
pcs
7 - Proceed with the installation of the specific
1
pcs
stem, tightening firmly to counter the stiffness of the
41
2
pcs
cables and to allow them to follow the curvature of
21
1
pcs
the guide.
23
1
pcs
8 - Check that the specific stem screws (4) are
24
present.
3Nm
9
pcs
25
1
pcs
9 - Place the expander (3) with a torque of 8 Nm,
ensuring that the fork pivot is cut to a height of 5 mm
1
pcs
below the upper surface of the stem. This way, the
19
22
1
pcs
shoulder of the expander will fill 2 mm, leaving 3 mm
1
pcs
to allow for proper headset compression.
1
pcs
10 - Place the screw and cap, then tighten to the
necessary torque to eliminate headset play; do not
1
pcs
exceed a torque of 2 Nm.
1
pcs
2.5Nm
3
pcs
11 - Align and tighten the stem screws to a maximum
5Nm
2
pcs
torque of 5 Nm.
14Nm
4
pcs
12 - The frame is not designed for a stem other than
14Nm
1
pcs
the LOOK LS3 stem.
14Nm
1
pcs
1
pcs
1
pcs
4Nm
7
set
HEADSET
14
5
13
15
6
16
7
17
30
20
32
12
31
12
26
41
43
28
41
42
29
26
27
23
19-1
18
34
38
36
34
33
Modification
EN
1
2
3
4
8
9
10
39
10
40
35
37
36
41
11
35
26
Resp
Date
Ind.
Material
Treatment
Publicité
