Publicité
BLAST BT
Battery-powered radio wind sensor
Dear customer, thank you for purchasing a Master S.p.A. product. Please read this manual carefully before performing the installation. The device has been designed to control
tubular motors for sun blinds and similar products. Any use other than the one defined by Master S.p.A. is forbidden and implies, along with non-compliance with the
instructions contained in this manual, the cancellation of Master S.p.A. responsibility and warranty. The installer must train the end user on the use of the automation device
and provide him with this use and maintenance manual for future reference.
This sensor does not protect the blinds in the event of sudden gusts of wind.
In case of this type of weather risks, make sure that the blinds remain closed! Master S.p.A. declines any responsibility for damage caused by adverse weather events not
detected by the device.
We respect the environment
Respect for the environment is everybody's responsibility! MASTER uses recyclable packaging materials. Dispose of the materials in the appropriate containers in accordance with local
. T
regulations
his product could contain substances that are polluting for the environment and dangerous for health. At the end of the life-cycle of the product, carefully follow the rules on the
most appropriate disposal. It is strictly forbidden and dangerous to dispose of the product by throwing it in the municipal waste
Notes on radio systems
Radio systems should not be used in areas with strong interference (e.g. near police stations, ports, airports, banks, etc.). However, a technical inspection should be carried out before installing any radio
system in order to identify any potential sources of interference. Radio systems can be used where disturbances or malfunctions of the transmitter or receiver, if any, are not a risk factor, or if this factor is
cancelled out by appropriate safety systems. The presence of radio devices operating at the same transmission frequency (433.42 MHz) can interfere with the radio receiver of the device, thus reducing its
range over the entire radio system and consequently affecting the operation of the system
Technical specifications
Power supply:
Battery 3V CR8-LHC
Dimensions:
236 x 54 x 73 mm
Weight:
200 gr
Working temperature:
–20°C / +55°C
Wind threshold values:
10 Km/h / 35 Km/h
Sun threshold values
( VEGA BT only):
1 Klux / 45 Klux Frequency:
433.42 Mhz
Operating range:
433.050 – 434.790 Mhz
Max. transmitted power, e.r.p. : <10 mW
Range (estimated):
20m
1. INSTALLATION
01.1 Safety instructions
maintenance of the product must be carried out only by a qualified and skilled technician, in compliance with the laws, regulations, local codes and instructions hereunder
electrical wiring must comply with the CEI standards in force. In conformity with the provisions of the Italian Ministerial Decree no. 37/2008, the electrical system must be
installed by an electrician. Some applications require a "dead man" control and may exclude the use of radio controls or require special safety features
condition should be regularly checked to prevent potentially dangerous situations
01.2 Installation instructions
Read the technical data in the section "Technical data" to evaluate the operating limits of the product
the product, make sure that it is compatible with the associated equipment and accessories
is intact and has not been damaged during
breakage of external or internal parts of the device
modify or replace any parts without the manufacturer's approval
made of a strong material and can guarantee a stable attachment
of the sensor is within the transmission-reception range generated by the sensor and the receiver of the automation device to be controlled
pointing downwards and with the sensor body in a horizontal position (the use of a bubble level facilitates the operation; thanks to the ±90° tilting wall mount the sensor can be
fixed even on non-vertical structures)
the movement of the blades
In case of more than one radio device in the same system, the distance between them must not be less than 1.5 m
near metal surfaces. Do not use abrasive products or solvents to clean the product. Do not use water jets or high-pressure cleaning systems. For safety reasons, do not stand near
the winding roller when the motor is energized.
01.3 Instructions for use
The product is not intended for use by persons (including children) whose physical, sensory or mental capabilities are
impaired, or with a lack of experience or knowledge, unless they have been able to benefit, thanks to the support of a
person responsible for their safety, from supervision or instructions on how to use the product
shutter, make sure that persons or property are not in the area affected by the movement of the shutter. Check the
automation device, when in operation and keep people away, at a safe distance
until the end of the movement
Children must not be allowed to play with the device and the roller blind while maintenance is being carried out (e.g.
cleaning of glasses, etc.). Disconnect the power supply line during maintenance
01.4 Installation
(1)
A
B
Anchor the base using
Tighten the two screws
the supplied dowels
that anchor the base to
and screws
the sensor
(1) ATTENTION: These screws should not be completely loosened.
(2) ATTENTION: When the switch is in the ON position, the LED1 should briefly blink. If the LED1 does not switch on, move the switch back to the OFF position (1), wait for 30
seconds and repeat the procedure.
transport. Violent shocks and the use of inappropriate tools can cause the
The device must not be cut or tampered with in any way. Do not
Make sure that the surface chosen for installation is
Make sure that the location chosen for the installation
The product must be exposed to the sun-wind, away from heat sources (e.g.: flue pipes), away from any obstacles that may interfere with
C
Place the two screw
covers
.
Before installing
Check that the packaging
Before operating the
D
E
(2)
Loosen the screw
Move the switch to ON to
and open the cover
under the sensor
VEGA BT
Battery-powered radio sun- wind sensor
X
Install the product with the blades
WIND Led
P1 button
P2 button
turn on the device
rev04 22.07.2017
The
The roller blind
Do not install the product
MANOEUVER Led
P3 button
F
Close the cover
Publicité
