Publicité
SYMBOL ICONS
Symbol shows the battery power, the longer the line is, the higher the power is.
Symbol shows hand-held display receives signals accurately.
Symbol shows that weight loaded on the crane scale is stable. It also shows that weight loaded on the
crane scale can be accumulated.
Symbol shows that the scale body is in the state of zero, or press "
zero.
Symbol shows that there is some data accumulated in the memory of the remote. Symbol will
disappear when data will be cleared.
Symbol shows Tare-function. The weight value will be the net weight.
Shows weighing unit is kg.
KEYBOARD FUNCTIONS
EN
"OK"
By pressing this key, either in weighing state or standby state, you can enter the function menu.
Press the key under menu or function setting to confirm.
Press "OK" button and go to menu F:
F
1
no function
F
2
no function
F
3
Date/time
F
4
no function
F
5
no function
F
6
no function
F
7
U 0
0 kg 1 lb
F
8
SN01
SN 00 see internal code, SN01, SN02.
F
9
P000
input the passwords 111 to go to menu S.
S
1
no function
S
2
dP 0
please select the decimal point among 0,1,2,3,4
S
3
full scale
F05000 to set the full capacity with 6 digits
S
4
no function
S
5
no function
S
6
modify the S menu passwords
"np": input the original passwords; "op": input the new passwords
S
7
no function
S
8
OFF 0
Power save mode
OFF
0
1: valid
S
9
function of changing the division value
"dd"
0
1:valid
", so that the device displays
0: invalid
0: invalid
12
"∧" and "∨"
Pressing these keys will cause a change in the options of the menu. These keys are also responsible for changing the
numerical values, once inside the individual menu positions. (For example: changing the individual numbers of the date
and time.)
"
》
"
This key is designed for switching between the desired number to be set inside the "date" and "time" menus.
"C"
When in the menu, press this button to go up one level in the menus. Repeatedly pressing this button will bring the display
into weighing mode.
"→0←"
Press this key to zero the current displaying value.
"→T"
Press this key to tare.
"F"
No function / not applicable.
"+"
Pressing the key under weighing state can keep current data in memory
"*"
If have accumulation data, pressing this key can review accumulated weights and times
"
"
Press this key to control the brightness.
Press this key to show "b xx", where "xx" means the brightness level, which can be adjusted by pressing keys "∧"and"∨",
then press "OK" button to confirm.
"xx" means that the effective value ranges from 02~15. The higher the number, the brighter it will be. As a result the power
consumption will also increase.
"-"
This button can clear accumulative data of the remote
"ON"
Power on
"OFF"
Power off
HOW TO TOTALIZE CURRENT WEIGHING DATA
Step 1: Hang the load on the scale
Step 2: Wait for data to be stabilized (displays stable symbol)
Step 3: Press"+"
Step 4: Instrument will display "Total accumulative data" and "accumulative times"
Attention:
Zero and minus weight cannot be accumulated.
One weighing value can only be totalized for one time, cannot be repeated to accumulate.
Can totalize 99 sets of data, save and turn off.
In case of accumulating wrong data, it is only necessary to clear the last data. There is no need to repeat the whole
accumulation procedure.
HOW TO REVIEW RESERVED DATA
If there is a need to check the subsequent accumulative data, please adhere to the following steps:
Step 1: Press"*"
Displays "accumulative total weights"
Step 2: Press"*"again
Displays "accumulative times"
Attention:
By pressing"*", the display will show the total weight and total times of accumulative actions. After 10 seconds the display
will go back to normal, weighing mode.
When there is no accumulative data in memory, pressing "*" will have no effect.
13
EN
Publicité
