Adjusting The Volume - Monacor TFT-2900LED Mode D'emploi

7 Operation
GB
The operation is identical for both monitors. The
monitors function independently of each other and
can be adjusted differently.
The on-screen insertions and menu settings
described here apply to the factory-set menu
language English (to switch to another language
menu item Language
7.1 Switching-on / stand-by mode
If the power indication (7) shows red after connect-
ing the power supply and if the screen remains
dark, the monitor is in the stand-by mode. To switch
on the monitor, press the button
indication is changed to green. To switch back to
stand-by, press the button
Note: The monitors have a low power consumption even in
stand-by mode. To switch off monitor unit and power sup-
ply unit completely if they are not in use for a longer period
of time, the power supply unit should be disconnected from
the mains socket to save power.
The monitor switched on reproduces picture and
sound of the last signal source selected. For the
first setting into operation the source at the HDMI
input (8) is selected. In the upper right corner of the
picture the following information is shortly inserted:
– identification of the source:
AV1 or
AV2
SVIDEO
HDMI
PC
– short information about the source, e. g. the
video standard (PAL or NTSC) for
the resolution of the graphics card for
Note: For the VGA input no information is inserted in the
upper right corner when
adjustment chapter 7.4) is displayed.
If the monitor does not receive any video signal
from the source, the screen is blue and no sound is
reproduced. Even with missing video signal, the
identification for the sources
SVIDEO
is shortly inserted, but not for the sources
HDMI and PC
appears in the centre of the picture.
7.2 Switching over the sources
1) Press the button SOURCE (2). A list of sources
is inserted, the source presently selected is
marked.
2) Select the source with the button
12
, chapter 7.5.2).
(6), the power
again.
source at the input
VIDEO 1 or VIDEO 2 (10)
source at the input S-VIDEO (13)
source at the HDMI TM input (8)
source at the VGA input (9)
AV1
Auto-Adjust
(automatic picture
AV1
, instead the message
3) Confirm the selection with the button SELECT
(5). After switching over to the source, the iden-
tification of the source and short information are
briefly inserted (
If the selection of a source is not confirmed, the list
is automatically deactivated when the insertion
time adjusted in the menu (menu item
chapter 7.5.2) has elapsed after the last button
has been pressed. The list can also be deactivated
with the button EXIT (1).

7.3 Adjusting the volume

Press one of the buttons VOL,
insert the adjusting scale for the volume. Then
reduce the value for the volume with the button
or increase it with the button .
The scale is automatically deactivated when the
insertion time adjusted in the menu (menu item
Duration
last button has been pressed. The scale can also
be deactivated with the button EXIT (1).
7.4 Automatic picture adjustment
For the source
TM
matic picture adjustment can be made with the but-
ton AUTO (3). Then manual adjustments on the
menu page
rected. After pressing the button,
inserted during the adjustment.
Note: An automatic picture correction is also made each
time the monitor is switched over to the source
after switching-on, however, in these cases the message
Auto-Adjust
7.5 Adjustments in the on-screen menu
1) To call the menu, press the button MENU (1), the
AV2
and ,
first menu page is inserted.
PC .
In the toolbar at the top the menu pages are
marked as follows:
1 st
depending on the video signal:
2 nd
, AV2 and
No-Sync
3
rd
only available for the source
2) To select a menu page, go to the respective icon
with the button
3) To select menu items on one page, use the but-
(2) or (3). ton
chapter 7.1).
chapter 7.5.2) has elapsed after the
PC
at the VGA input (9) an auto-
FUNCTION (
is not always displayed as an indication.
PICTURE
page ,
or picture adjustment
page SYSTEM :
basic adjustment
page FUNCTION ,
manual picture adjustment
(4) or
(2) or (3).
Duration
(4) or (5), to
chapter 7.5.3) are cor-
Auto-Adjust
is
PC
and
PC :
(5).