Publicité
2.1.5.
DOVER
•
OUTDOOR AIR INTAKE:
The Dover model has the possibility of choosing whether the primary and secondary air intake comes from; an adjacent
environment (or even from the outside of the house) or from the same room in which the stove is installed.
The primary air inlet of these models is placed at the back of the stove, so if the stove is not channelled to the outside, a
minimum separation between the stove and the wall of at least 6-8 cm must be left, so that the air supply for combustion is
sufficient. If it is decided to supply primary air from outside or from an adjacent environment, it will be sufficient to connect
this inlet through a 120 mm diameter pipe to the chosen place. Keep in mind that a too long pipe or with too many deviations
(elbows),is far from benefiting the air intake, actually, what it causes is a great loss of air feeding and therefore can cause
combustion problems. (See drawing D2.34).
GLASS TOP OF THE STOVE
•
In this model, optionally you have the possibility to choose that the top of the stove is made of glass. It is a 10 mm thick tempered glass
(TAPA-D). In order to place it, just place it on the existing top of the stove. You can use anticaloric silicone, which can be purchased at the
same Bronpi distributor where you purchased the stove, to make the glass stuck with the top in order to ensure the placement of the same
and prevent its movement.
Attention!!! You must place the glass lid, before proceeding to the placement of the smoke evacuation tubes of the stove.
2.1.6.
CROACIA-T
This model of stove is equipped with a turbine of 225 m3/h suitable to improve the distribution of the heat through
the air circulation of the environment.
The air circulation can be regulated by a switch of three positions located in the bottom right side (see drawing
D2.35).
These three positions have the following functions:
-
Position 0: tThe turbine will remain off even if there is combustion inside the fireplace, so you have to
position the switch in the position 1 or 2 if you want the turbine to operate.
-
Position 1: the turbine runs continuously at slow speed.
-
Position 2: the turbine runs continuously at fast speed.
•
TURBINE CONNECTION
On the right rear of the stove we can find the conductor that connects to the grid (see drawing
D2.36).
It is advisable not to cut it in its length completely since this section is useful when replacing
electrical components. The correct connection to the ground system is essential.
Installation of the appliance must be carried out by qualified personnel in accordance with the
current regulations of the sector.
•
TURBINE REPLACEMENT
In case of replacement of one of the electrical components, the replacement operation will be
carried out by removing 4 screws from the bottom, as shown in the drawing. Disconnect and
replace the damaged item and reassemble everything the way was assembled.
2.1.7.
VERSALLES
Versalles-C
In order to install the Versalles-C series, a metallic Z-shaped piece is provided, that you have to
screw on the wall and will support all the weight (see drawing D2.37).
IMPORTANT!!!: it is necessary to assure that the wall will support the weight of the fireplace (and the weight of the wood).
It is not recommended to install the fireplace on walls made of materials that are not able to support the weight or made of
combustible materials.
•
OUTDOOR AIR INTAKE
In the models of the Versalles series, it is possible to choose that the entrance of primary air comes from a contiguous place or even from
outside of the house.
In the case of providing air from outside or from a contiguous place, you must purchase the optional kit (KIT-AIR2) for external air intake
(airtight). Simply connect the KIT with a 100 mm diameter pipe to the chosen place. Keep in mind that a too long pipe or with too many
deviations (elbows), far from benefiting the intake of air, causes a great loss of load and, therefore, can cause combustion problems.
Do not forget that this external air intake is independent and different from the input needed for the ventilation unit (turbine).
The procedure for placing the optional external air intake kit is as follows (see drawing D2.38):
-
Position the kit below the plane of fire. You must center the kit and position it on the front (inner face) as indicated in the image.
-
With the supplied self-drilling screws, connect the kit to the base of the appliance.
-
Connect the air intake to the exterior or selected environment through a 100 mm diameter pipe.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
25
D2.34
D2.35
D2.36
D2.37
STOVES
Publicité
