Télécharger Imprimer la page

Bronpi TUDELA Instructions D'installation, D'utilisation Et D'entretien page 11

Masquer les pouces Voir aussi pour TUDELA:

Publicité

FUEL LEVEL
The maximum load recommended for the Bombay series models is reflected in section 12 of this
manual: "Technical Data Sheets - Exploded view". However, in the rear vermiculite you will also
find marked the maximum level of fuel that should not exceed. (See drawing D2.51)
Keep in mind that you must never overload the device. Too much fuel and too much air for
combustion can cause overheating and therefore damage the device. Failure to comply
with this rule will cancel the warranty.
3.
INSTALLATION AND SAFETY INSTRUCTIONS
The way of installing the stove will affect the safety and the proper operation. For this reason, it
is recommendable that the installation is carried out by people who are qualified and informed
about the compliance with the installation and safety norms. If a stove is not properly installed it
may cause serious damage.
Before the installation, follow the next verifications:
Make sure that the floor can sustain the weight of the equipment and make a proper isolation in the case that it is made of flammable
material (wood) or a material that can be affected by a thermal shock (plaster cast, for example).
If the equipment is installed on a floor which is not completely refractory or inflammable such as parquet, carpet, etc, it is necessary
to replace this part or introduce a fire-resistant base so that it protrudes out the fireplace 30 cm. Example of materials include steel
flooring, glass base or any other type of fire-resistant material.
Make sure that there is proper ventilation in the place where it is installed (air intake) (see section 5 of the manual).
Avoid the installation in places where there are collective ventilation pipes, hoods with or without extractor, B type gas equipments,
heat pumps or equipments that can cause that the draw of the stove is not good if they are used at the same time.
Make sure that the smoke duct and the pipes used for the chimney are suitable for the operation of the stove.
We recommend that you call your fitter in order to check both the chimney as well as the air flow for the combustion.
This product can be installed near the walls as long as the they comply with the following requirements:
The fitter must assure that the wall is completely made of brick masonry, thermo-clay block, concrete, bricks, etc, and that it is coated
by materials that can support high temperature.Therefore, for any other type of material (drywall, wood, non-ceramic glass, etc), the
fitter must provide sufficient insulation or keep a minimum safety distance to the wall of 80-100 cm.
Keep any flammable or heat sensitive materials (furniture, curtains, and clothing) at a minimum distance of about 100cm, including the
area in front of the loading door. Measurements below the minimum distances should not be used.
3.1.
SAFETY MEASURES
During the installation of the equipment, there are risks to be taken into account, so you should follow the next safety measures:
a.
Do not place flammable objects above.
b.
Do not place the stove near combustible walls.
c.
The stove should only be used when the ash pan is inserted.
d.
It is recommended to install carbon monoxide detector (CO) in the room where the equipment is installed.
e.
Use the glove included for opening and closing the door as well as manipulating the controls as these can be very hot.
f.
Solid combustion residues (ashes) should be collected in an airtight container and resistant to fire.
g.
The appliance should never be turned on in the presence of emission of gases or vapours (e.g., linoleum glue, gasoline, etc).
h.
Do not place nearby flammable materials.
WARNING!!
It is noted that both the stove and the glass get very hot and should not be touched.
3.2.
INTERVENTION IN CASE OF EMERGENCY
If there is fire in the stove or the flue:
a)
Close the loading door.
b)
Close primary and secondary air intakes.
c)
Put the fire out by using carbon dioxide extinguishers (CO2 powder).
d)
Request for the immediate intervention of the fire-fighters.
DO NOT PUT THE FIRE OFF WITH WATER.
WARNING:
The manufacturer declines any responsibility for the malfunction of an installation not subject to the requirements of these
instructions or the use of additional products not appropriate.
4.
CHIMNEY
The chimney is of basic importance in the proper functioning of the stove and primarily has two functions:
-
Evacuate the smoke and the gas safely out of the house.
-
Provide sufficient draft to the stove in order to keep the fire.
Therefore, it is essential that it is made perfectly and that it is subjected to maintenance operations in order to keep it in good condition
(many of the claims due to malfunctioning reasons refer exclusively to a bad draft). The chimney can be made of masonry or metallic pipe
compound.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
28
D2.51
STOVES

Publicité

loading