General Indications - Miche SWR T Manuel D'utilisation Et D'entretien

ENGLISH

GENERAL INDICATIONS

1
We thank you for buying the SWR T wheels, product that will gua-
rantee you security and functionality through the years.
Before proceeding with using the wheels, please read carefully the
following instruction and store them in a safe place for eventually
reusing. Fac Michelin S.r.l. reserve to modify the content of this
manual without notice. The updated version will always be avai-
lable www.miche.it
On our website you will also find information on the other Miche or
SWR products and the spare parts catalogue.
In the box of wheel set you will find:
• The font and the rear wheel
• The quick release set
• The valve extension
• Vibrostop
• Zero point
• Two pairs of sintered brake pads for carbon rims
• Wheels bag
• The manual of instructions and use of SUPERTYPE Wheels.
Warning
!
Any modification or alteration (and graphic) of the product with
non-original spare parts or spare parts not delivered directly
by Fac Michelin S.r.l., involves the expiration of the guarantee.
Warning
!
Direct and violent impacts on broken road surfaces can cause
damage to the rims. Such damage is outside the conditions of
our guarantee and repair costs will be charged directly to the
customer.
Warning
!
In case of strange impact caused from bad road base or wheels
transport, we trust to bring the wheels to your mechanic for a
check.
Warning
!
Using only MICHE brake pads for carbon rim that you find inside
SWR T wheel set box. Use original spare parts exclusively pro-
vided by Fac Michelin Srl.
Warning before using the bicycle:
• Check for proper operation and state of wear of all the compo-
nents before starting to ride.
• Check the condition and pressure of the tyres fitted to your Mi-
che wheels.
Please consult the manufacture of your tyres/tubulars of choi-
ce when inflating your tyres/tubulars.
• Check your wheel(s) spoke tension, to ensure there are no
spokes with low spoke tension. In the event of any spokes not
being at the correct tension please note that any spoke tension
adjustments must be carried out by a specialist skilled cycle
mechanic.
• Check that the wheel quick release are correctly closed to en-
6 SWR T / MICHE.IT
sure the wheels are held in the cycle frame correctly, see (Fig.7)
Attention incorrect use or the loosening of the quick release
could lead to a serious or fatal accident.
• Check very carefully the alignment of the front and rear brake
calliper brake blocks, ensuring the break only on the correct
braking surface of the Miche wheel rim(s) also check for, and re-
move, any foreign particles which may be imbedded in the break
pad. [Please note you may need to remove your Miche wheels
from your cycle to do so]
• When riding in wet conditions, remember that the stopping po-
wer of your brakes is greatly reduced and the adherence of the
tires to the ground is considerably reduced. This makes it harder
to control and stop your bicycle in wet conditions to avoid an
accident. An accident could results in severe personal injury or
death.
• To the users of more than 85kg weight, Fac Michelin suggests to
check the wheels status to the mechanic every two months or
every 1,500km.
• We reccomend using these wheels if you weigh more than
102 Kg
• Never wash the pieces with pressure-fed water because water
may get through the seals and cause permanent damage to the
internal components. We recommend washing components with
a sponge, mild soap, and water.
• Salt water environments (as found on winter roads and neat the
seaside) can cause galvanic corrosion on most bike parts. Care-
fully rinse, clean, dry and re-lubricate all exposed parts to avoid
damage, malfunctions and accidents.
•
HUBS
2
Warning
!
If you have any doubt whatsoever your service-repair ability,
please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
Use original spare parts exclusively provided by
Fac Michelin S.r.l.
When replacing any broken sealed bearings please ensure sealed
bearing correct measure and specification are used.
Rear hub
Right side 26x17x5 (6803)
Left side 26x17x5 (6803)
Free wheel 26x17x5 (6803)
The SWR T hubs are easy to maintain. To do it, proceed as follows:
FRONT HUB
Front hub
24x12x6 (6901)
24x12x6 (6901)