Miche SWR T Manuel D'utilisation Et D'entretien page 8

below:
• Correct spoke tension for front wheel: 900 N.
• Correct spoke tension for rear wheel, free wheel side: 1300 N.
• Correct spoke tension for rear wheel, opposite free wheel side:
800/1100 N.
To evaluate the correct wheel tension, please use a professional
spoke tension gauge, we do not recommend that spoke tension
is estimated manually; please refer to a professional cycle me-
chanic if you do not own a professional spoke tension gauge. The
correct spoke tension is essential to ensure a ridged and durable
wheelset.
ATTENTION in correct spoke tension, too high or too low, could
lead to wheel failure and resulting serious or fatal accident.
COMPLETE WHEELS
4
SWR T Wheels are developed to set up tubular, and designs for use
solely on the road. Please ensure that the wheels are not subject to
direct shock from poor road surfaces [i.e. pot holes] ATTENTION
direct shock to the wheels from poor road surfaces could lead
to wheel failure and resulting serious or fatal accident. In the
event your wheels are subject to any such shocks from poor road
surfaces, yet do show the signs of any damage we advise you to
immediately have the wheels checked by a qualified mechanic or
other qualified person. ATTENTION failure to check your wheels
after they have been subject shock as described above, even
if they show no visable signs of damage, could lead to wheel
failure and resulting serious or fatal accident.
QUICK RELEASE
The SWR wheels quick release has already attached in the wheel
pack.
The quick release lever has two fixed positions:
• OPEN (the text OPEN is visible)
• CLOSED (the text CLOSED is visible)
Every time you will use your bicycle, check carefully that the quick
release levers are on the position CLOSE (with the lever in closed
position, on the front side of the quick release the mark CLOSE
must be present) (Pic.7).
Attenzione
!
Please ensure the quick release lever is closed correctly and in
the correct position. Failure to do so could lead to wheel failure
and resulting serious or fatal accident.
All the positions different from the closed position have to be con-
sidered extremely dangerous.
For the correct closing of the quick release:
• Starting from the opened position of the lever, making the nut
contact with the fork manually
• Bringing the lever from the opened position to the closed only
with the hand power (Pic.7)
• Turn manually with your fingers the quick release nut until its
sits against the cycle dropout, ensuring the quick release lever
is sitting in the "open position" (Pic. 7)
• Don't use any tools (ex: tubes, extensions, ...); the closing stress
has to be felt in the passage from the opened to the closed po-
sition (Pic.7).
• You never have to use the quick release lever as a nut to close
the quick release, because it will injury the quick release (Pic.8).
8 SWR T / MICHE.IT
ATTENTION, turning the quick release lever to tighten the
quick release could result in damage to the quick release and
cycle frame dropout, which could lead to wheel failure and
resulting serious or fatal accident.
• Given that the wheels will be used on irregular surfaces, im-
pacts, hits or a fall can cause also damage which cannot be
visible with fast locking. If one of these conditions is detected,
please visit a qualified mechanic or special personnel for an
accurate inspection of the locking, since its damage may
cause accidents, and serious or fatal injuries.
• After every washing, remove the locking from the hub and grea-
se the pin completely to prevent oxidation.
FITTING OF TUBULAR
5
Warning
!
If you have any doubt whatsoever your service-repair ability,
please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
To fit the tubular tyre, follow carefully the instructions enclosed
with the tyre.
Warning
!
If at any point whilst fitting the tubular tyres to your Miche
wheels you have any doubt as to how the tubular tyre has been
fitted please consult a qualified cycle mechanic. The fitment of
tubular tyres to Miche wheels is a specialist skill. Incorrect fit-
ting of tubular tyres to Miche wheels could lead to wheel failure
and resulting serious or fatal accident
FITTING OF VIBROSTOP
6
• Clean the area of application of the "Vibrostop"
• Insert the "Vibrostop"
• Press firmly the "Vibrostop" once fitted to the rim