General Indications - Miche Carbo Graff Manuel D'utilisation Et D'entretien

ENGLISH

GENERAL INDICATIONS

1
We thank you for buying the Carbo Graff wheels, a product that will
guarantee you security and functionality through the years.
Before proceeding with using the wheels, please read carefully the
following instruction and store them in a safe place for eventually
reusing.
In the box you will find:
• The front wheel arranged with TX-12 system
• The rear wheel arranged with TX-12 system
• Wheel bag
• The manual of instructions and use of Wheels
• Brake rotor lock ring
Warning
!
Any modification or alteration (and graphic) of the product with
non-original spare parts or spare parts not delivered directly by
Fac Michelin S.r.l., involves the expiration of the guarantee.
Warning
!
Direct and violent impacts on broken road surfaces can cause da-
mage to the rims. Such damage is outside the conditions of our
guarantee and repair costs will be charged directly to the customer.
Warning
!
In case of strange impact caused from bad road base or wheels
transport, we trust to bring the wheels to your mechanic for a
check.
Warning
!
Tyre width section: min 35 / max 45
Warning
!
Only Shimano original lock ring designed for through axle internal
diameter 27mm to be used with the disc brake.
Warning before using the bicycle it is necessary to:
• Check for proper operation and state of wear of all the components
before starting to ride.
• The rims have been made with great dimensional precision. If fitting
a tyre on a rim is too easy, it may be too big and this will have signi-
ficant implications for safety. We therefore recommend using only
high quality tyres that require the use of clincher tyre levers and a
reasonable amount of strength to fit them. Using a tyre that is too
big for the rim may cause the tyre to rupture unexpectedly and
cause accidents, physical injuries or even death.
WARNING! Incorrect rim / clincher tyre coupling may cause it to
deflate, burst or detach suddenly and cause accidents, serious
injuries or even death.
• Check the condition and pressure of the tyres fitted to your Miche
wheels. Pressure must not exceed the limit of 5,5 bar and 80 psi
signed behind valve hole. The inflating pressure of the tyres must
NOT exceed the LOWER pressure level between the maximum pres-
sure stated by the tyre manufacturer.
6 CARBO GRAFF / MICHE.IT
Excessive tire pressure reduces the grip of the tire on the road and
increases the risk that the tire will unexpectedly burst.
Inflation pressure that is too low reduces tire performance and incre-
ases the probability of sudden and unexpected loss of tire pressure.
In addition, premature damage to the rim may occur. Incorrect tire
pressure could cause tire failure or loss of control of the bicycle,
resulting in an accident, personal injury or death.
• Check the tension of the spokes so as to notice any spokes which
got loose. In the case spokes are loose, contact a qualified mechanic
or special personnel to perform the tensioning.
ATTENTION, the use of wheels not centered properly or with spo-
kes broken and/or loosen or damaged may cause an accident,
serious injury or death.
• Check that the braking system and the brake pads in the brake cali-
pers are in good state and that the screws on the disc or the locking
ring of the disc, depending on your model, are properly locked.
• To the users of more than 85kg weight, Fac Michelin S.r.l. suggests
to check the wheels status to the mechanic every two months or
every 500km.
• If the total weight of your bike and various parts installed
exceeds 100 kg, not used these wheels
• Never wash the pieces with pressure-fed water because water may
get through the seals and cause permanent damage to the internal
components. We recommend washing components with a sponge,
mild soap, and water.
• Salt water environments (as found on winter roads and neat
the seaside) can cause galvanic corrosion on most bike parts.
Carefully rinse, clean, dry and re-lubricate all exposed parts to
avoid damage, malfunctions and accidents.
• If your component shows signs of rust, this means it has to be
changed urgently as it might be a sign of damage.
HUBS
2
Warning
!
If you have any doubt whatsoever your service-repair ability,
please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always wear
gloves and protection glasses.
Use original spare parts exclusively provided by Fac Michelin S.r.l.
When replacing any broken sealed bearings please ensure sealed
bearing correct measure and specification are used.
Rear hub
Right side 26x17x5 (6803)
Left side 26x17x5 (6803)
The XGRAFF hubs are easy to maintain. To do it, proceed as follows:
Front hub
26x17x5 (6803)
26x17x5 (6803)