DeVilbiss Healthcare Drive 1025DS Guide D'instruction page 5

WARNING
Risk of injury or damage
When the device is operated at the extremes of the environmental operating specifications (i.e., maximum temperatures and humidity), and in a single fault condition,
•
which is a single component or performance malfunction, such as a blocked exhaust vent, blocked air intake, or an internal cooling fan failure, the temperature of the
air coming out of the exhaust vents, located on the bottom left and bottom right sides of the unit can reach temperatures capable of causing a burn injury (see stated
temperature and contact time values in the model specific tables below).
Keep exposed body parts, such as hands and feet, a minimum of 62 inches (1.6 meters) away from the exhaust vents to avoid the risk of burns. Single fault conditions
•
may result in visual and audible alerts and alarms .
• NOTE – Under normal and single fault conditions, the concentrator releases warm air out the bottom of the unit (exhaust vents) which may discolor temperature
sensitive flooring surfaces. The concentrator should not be used over flooring that is sensitive to heat staining. The Manufacturer is not responsible for flooring that
becomes discolored.
• Operate the unit in a cool, dry area with good ventilation, located on a hard surface, avoid thick rugs or carpeting . NEVER block the air intake or exhaust vents . Keep
the unit a minimum of 12 inches (30.5 cm) away from any wall, draperies, or any other objects that might prevent the proper flow of air in and out of your oxygen
concentrator. Proper air flow is needed to prevent overheating of the oxygen concentrator. DO NOT place the concentrator near any heat source such as hot air
registers or heaters . Overheating of the oxygen concentrator may lead to low oxygen output and a risk of burns .
The oxygen concentrator should be located in a well-ventilated area. DO NOT operate the unit in a closed or confined space, such as a closet, bathroom, etc. Avoid
•
operating the device near smoke pollutants and fumes .
Under extreme environmental conditions and a single fault condition occurs, the following device surface temperatures may exceed 106 °F (41 °C). See Table 1
•
below for the model specific maximum temperature and safe contact guidance:
Table 1 - 1025DS Series
Description
Air coming from exhaust vents located on each
side near the bottom of the unit
Oxygen outlet fitting
Power Switch
Flow meter knob
LED Indicator panel
Cannula at the outlet
Table 2 - 1025KS Series
Description
Air coming from exhaust vents located on each
side near the bottom of the unit
Oxygen outlet fitting
Power switch
LED Indicator panel
Cannula at the outlet
Table 3 - 1025UK Series
Description
Air coming from exhaust vents on each side near
the bottom of the unit
Oxygen outlet fitting
Power switch
LED Indicator panel
Cannula at the outlet
CAUTION
Federal (U.S.A.) law restricts this device to sale by or on the order of a physician.
•
It is very important to follow your oxygen prescription. Do not increase or decrease the flow of oxygen – consult your physician.
•
Use of harsh chemicals (including alcohol) is not recommended. If bactericidal cleaning is required, a non-alcohol based product should be used to avoid inadvertent
•
damage .
A-1025DS
Maximum Temperature
1025DS Series
°F °C
158 .7 70 .4
118 .9 48 .3
132 .1 55 .6
126 .3 52 .4
122 .5 50 .3
119 .8 48 .8
Maximum Temperature
1025KS Series
°F °C
155 .1 68 .4
108 .0 42 .2
112 .5 44 .7
109 .8 43 .2
108 .7 42 .6
Maximum Temperature
1025UK Series
°F °C
158 .7 70 .4
109 .0 42 .8
109 .9 43 .3
111 .0 43 .9
109 .2 42 .9
Max safe contact time
Less than 1 minute
Less than 1 minute
Less than 1 minute
Less than 1 minute
Less than 1 minute
Less than 1 minute
Max safe contact time
Less than 1 minute
Greater than 10 minutes
Less than 10 minutes
Less than 10 minutes
Greater than 10 minutes
Max safe contact time
Less than 1 minute
Greater than 10 minutes
Less than 10 minutes
Less than 10 minutes
Greater than 10 minutes
EN - 5