Güde 320/25 LI-ION Mode D'emploi page 13

Masquer les pouces Voir aussi pour 320/25 LI-ION:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
The battery must be charged to the full extent
before being used for the first time
The mower is automatically switched off when
the battery voltage is low. In such a case, the
battery must be charged.
The battery should be charged before longer
breaks, e.g. before winterising.
The battery may be charged in any state of
charging and charging may be interrupted at any
moment without this causing any damage to the
battery.
1.
Take out the start key.
2.
Use your finger to push the battery cover and
release it.
3.
Take the battery out of the compartment.
4.
Connect the battery to the charger.
5.
Plug the charger (230V~).
Instructions for Charger
Green LED permanently on: Ready for operation
Red LED permanently on: Battery being charged.
Green LED permanently on when battery is
inserted: Battery is fully charged.
Instructions to the battery charge indicator
If the button on the battery is kept pressed, the charge
level can be read:
3 green LED are on: Battery is fully charged.
2 green LED are on: Battery is half full.
1 green LED is on: Battery is almost empty.
Caution: The battery reaches the maximum
capacity after 3-4 charges.
Mounting the collection box (pic. 8)
Fit the collection box as shown in the picture.
Operation
Caution! Rotating blade
Works/adjustments on the machine only to be performed
when the engine is off, start key removed and the cutting
blade idle.
The duration of work with a charged battery depends on
the cut grass.
The higher and thicker the grass, the shorter time you
work with a charged battery.
General information on the operation
Start key
Caution! Rotating blade
Before any adjustment:
Take out the start key
Do not touch the rotating blade
The mower may only be started when the start key is
inserted in the machine.
Hanging the collection box (pic. 9)
Fit the collection box as shown in picture 9.
Cutting height adjustment (pic. 10-12)
Cutting height is given by readjusting the axis and the
wheels.
Hold the wheel and unscrew the
wheel cover.
Take the axis out and put it to
the guide in the required height.
Make sure both the front and rear axis is installed in the
same height.
SWITCHING the mower ON/OFF (pic. 2)
Start the mower on a flat surface.
Do not start it in high grass. Tip the mower over in high
grass if necessary.
Starting the engine:
Press the ON button (pic.2/2)
With ON being pressed, pull the safety handle (pic.
2/1).
Release the ON button (pic. 2/2)
Switching the engine off:
Release the safety handle (pic. 2/1).
Emptying the collection box
The filling indicator flap goes down when the collection box
is full.
Caution! Rotating blade
Works/adjustments on the machine only to be performed
when the engine is off, spanner pulled out and the cutting
blade idle.
Unhook and empty the collection box.
Remove any obstruction in the cutting area.
Refit the collection box as shown in picture 9.
At regular intervals, clean the openings below
the filling indicator in the collection box.
Warranty
A warranty period of 12 months applies to commercial use
and 24 months apply to private use and commences on
the day of purchase of the device.
Warranty applies exclusively to failures due to defective
material or workmanship. An original sale slip with
indication of date of sale must be presented in case of
claiming for the warranty rights.
Warranty does not cover unprofessional use such as
device overload, violent use, damage caused by third party
or foreign materials, failure to comply with operations and
assembly manual, and normal wear and tear.
Residual risks and protective measures
Mechanical residual risks:
Risk
Description
Cutting,
Rotating blades
amputation
may cause
serious cutting
injuries or
amputation of
parts of your
body.
13
Protective measure(s)
Never touch under the
cover when the machine is
being operated.
Wear protective shoes
Never remove the
collection box when the
machine is being
operated.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

95538

Table des Matières