Peg-Perego PRIMO VIAGGIO SLK Notice D'emploi page 12

Base Twist, put the handlebar in the carry position
and pull the lever on the backrest upwards while
simultaneously lifting the car seat.
4 The car seat handlebar has four fixed positions. To
rotate it, press the two buttons on the handlebar and
move this to the required angle. Ensure it clicks into
position.
• Position A: the in-vehicle position;
• Position B: the position for transport by hand and for
installation on a base, stroller or chassis;
• Position C: this is the resting position;
• Position D: stops the car seat from rocking.
Instructions for use without base
5 IMPORTANT! The car seat must be parallel to the
ground. If necessary, use rolled-up towels or swimming
pool float tubes under the car seat, in the folds of the
vehicle's seats.
Fit the car seat with the child seated inside,
remembering to secure the child with the harness. Fully
lower the handlebar of the car seat (point 4 -position A).
6 Slide the lower part of the vehicle seatbelt into the two
guides on the car seat handlebar (fig_a) and buckle it
(fig_b), ensuring the seatbelt is taut, as shown in the
figure.
Grasp the upper part of the vehicle seatbelt and pass it
behind the car seat backrest (fig_c).
7 Insert the belt into the rear guide (fig_a). Tighten the
vehicle seat belt (fig_b). Installation is now complete.
8 To release the harness, press the red button on the
crotch strap buckle (fig. a) and remove the straps. To
engage the harness, place the two shoulder strap
tongues in position and insert them into the buckle of
the crotch strap until they click into place (fig. b).
9 To slacken the harness, insert a finger through the seat
opening (1), keep the metal button pressed, and with
the other hand pull on the straps (2).
10 To tighten the straps until they are snug to the child's
body, pull the central adjustment strap towards you.
CAUTION: Do not over-tighten the straps, and
ensure you leave minimum slack.
11 IMPORTANT! In winter, do not strap the child into
the car seat wearing bulky, heavy clothing, and do
not place blankets between the child's body and the
harness. This could cause incorrect positioning of the
safety harness, with serious consequences in the event
of a collision.
Use a blanket or an approved Peg Perego accessory to
protect your child from the weather.
12 The harness and the "Side Impact Protection" headrest
can be adjusted simultaneously to 6 different heights so
as to follow the growth of the child.
To adjust the height, press the rear height adjustment
button (on the car seat backrest) and at the same time
raise or lower the straps and headrest to the required
position, ensuring that they click into place. Slacken
the shoulder straps before adjusting the height of the
harness and headrest.
13 The headrest may be set in 6 different positions.
22
14 The safety harness is at the right height when the slots
in the backrest are at shoulder height or just below
(green area), as shown in the figure.
Make sure the straps are not in the red area.
15 This car seat features the Dual Stage Cushion, a system
composed of 2 separate cushions for even the smallest
babies.
a: headrest reducer
b: seat reducer cushion
Do not use the Dual Stage Cushion with children
over 61 cm in height and 9 kg in weight.
16 The special shell shape is designed to rock your child.
To rock the child gently, put the handlebar in the carry
position, as shown (fig_a).
To prevent oscillation and stop rocking, lock the
handlebar behind the backrest (fig_b).
17 The hood provides your child with shade and shelter.
IMPORTANT: The hood must not be used to lift
the car seat because it might detach.
18 To remove the hood, release the elastic bands behind
the handlebar (1), lift it and release it upwards (2).
19 The seat is fitted with Kinetic Pods, to ensure greater
safety in the event of a side impact.
FULLY open the Kinetic Pod by turning it clockwise
(fig_a). To return the pod in the initial position, turn it
anti-clockwise (fig_b).
20 ATTENTION: ONLY open vehicle door side Kinetic
Pod.
IMPORTANT: Make sure the Kinetic Pod situated on the
side facing the inside of the car is never pulled out.
How to use the car seat on the aircraft
This unit is certified for aircraft use.
21 Position the car seat on the aircraft seat with the
backrest in the most upright position. Adjust the
handlebar in the forward most position as shown.
Thread the lap belt through the slots in the handlebar
and lock the latch plate into the buckle. Pull the strap to
tighten the seat belt.
IMPORTANT! Use only on forward facing seats. If
the car seat can not be properly secured ask for flight
attendant help.
IMPORTANT! Do not use the base to install the car
seat on an aircraft seat.
Removing the soft cover
22 To remove the "Dual Stage Cushion": unbutton the two
buttons (fig_a) anchoring the headrest reducer to the
seat reducer cushion and pull it off.
23 Open the harness and remove the shoulder straps.
Remove the seat reducer cushion, sliding it off the
crotch strap.
24 From the back of the car seat, pull the straps out the
front.
25 Release the four elastic bands on the cover from
underneath the handlebar (fig_a), pull out the crotch
strap (fig_b) and remove the entire cover.
26 Slide off the headrest cover from the bottom first and
23