Télécharger Imprimer la page

Patton Kamado 20 Instructions De Montage Et Mode D'emploi page 32

Cuiseur

Publicité

Les langues disponibles
  • FR

Les langues disponibles

REFUELING
With the vents closed, the Kamado stay at a high temperature for several hours. If you require a longer
cooking time (e.g when roasting a whole joint or slow smoking), it may be necessary to add more charcoal.
Just add some additional charcoal and continue as above.
REPLACING THE FELT PACKING ON THE KAMADO GRILL
Depending on how you use the Kamado Grill, the felt packing around the lid and the base should be replaced from time to
time. This prevents "false air" from occurring. Carefully carry out the following:
Requirements:
- self adhesive felt packing
- open-ended spanner
- scraper and/or Stanley Knife
- pot scourer of abrasive pad
- acetone
- masking tape
1.
Remove the adjustable cut-off or ceramic lid cap. Unscrew the nuts on the top tensioning band with the
spanner, then next, carefully lift off the lid and lay it upside down onto a protective layer on the floor.
Make sure that you do not drop the lid!
2.
Unscrew the bottom tensioning band and leave the ceramic base standing in the housing or on the table.
3.
Using the Stanley Knife or scraper, cut or scrape off as much of the existing felt packing as possible.
Remove the remaining bits of felt and glue with the acetone an the action of an abrasive pad or pot scourer
4.
Now you must wait for about one hour until the acetone has evaporated.
5.
Carefully stick the new (self adhesive) felt packing to the edge of the base and the lid. Make sure that the
seams are not at exactly the same place again and allow the felt to overlap slightly on the outside, which is
better than on the inside (because it will burn when the grill is lit once again). Allow a little play when sticking
down the felt packing (therefore not too tight or stretched), so when warming up the felt packing is able to
shrink a little. Neatly cut the felt packing at the seam. It you are using adhesive in place of self adhesive tape,
please do as follows:
Apply the masking tape immediately under the edge of the base and the outside of the lid so that the adhesive
does not stick to the Kamado Grill itself. Protect the inside of the grill with a piece of cardboard and then spray
the edges with the adhesive. Follow the instruction for the adhesive and allow it to dry and then stick the felt
packing onto the edges. Allow the glue to completely harden.
6.
Reassemble the Kamado Grill. Place the tensioning band against the base and tighten the nuts. Carefully put
the lid into the top tensioning band and tighten the nuts. Check whether the lid and the tensioning bands are
straight and then give the nuts a final tighten.
TERMS & CONDITIONS OF THE LIMITED GUARANTEE FOR THE PATTON KAMADO GRILL
Every Patton Kamado Grill ceramic cooker has a limited guarantee covering the materials and construction of all tyhe
ceramic components (e.g. canopy, frame, flu with cut-off, fire basket and inner ring). This guarantee is effective for as long
as the original purchaser remains in possession of the Patton Kamado Grill or the covered component.
The Patton Kamado Grill has a limited manufacturer's guarantee of 2 years for the original purchaser. The ceramic
components are not covered for breakages caused by dropping or misuse. The components made from metal, stainless
steel or cast iron on the Patton Kamado Grill (e.g. metal bands, hinging mechanism, metal covers with double function,
grill, fire basket and regulating slide) have a limited manufacturer's guarantee of 1 year for the original purchaser.
Patton endeavours to use only rustproof materials and paint that can resist high temperatures and is used on the metal
surfaces. However, metal materials and protective finishing coats can be affected by surface cracking or exposure to
various substances and circumstances over which Patton has no control.
Bleach, industrial vapours, chemicals, artificial fertiliser, extreme humidity, pesticides for the lawn and salt are but a few of
the substances that can adversely affect paint and finishing materials on metal coverings. For this reason, the guarantee
DOES NOT COVER RUST, OXIDISATION, FADING or any other DEFECTS to the metal, stainless steel and cast iron
components, unless this also leads to the loss of the structural integrity or defects to the components on the Patton
Kamado Grill. This product must be kept indoors during the winter period. The crackleware finish of the ceramics is part of
the production process.
Wooden articles, such as bamboo side tables, have a limited manufacturer's guarantee of 1 year for the original
purchaser. Wooden products are not covered against normal weathering or cracking unless this affects the structural
integrity. The thermometer also has a limited manufacturer's guarantee of 1 year.
GB, IE
32

Publicité

loading