Colour Spotlight; Interconnecting Several Parl-7Dmx Units - IMG STAGELINE PARL-7DMX Mode D'emploi

After 15 seconds the flashing stops and the
selected programme starts. The yellow LED MAS-
TER (4) lights up. For a quicker start of the pro-
gramme keep button MENU pressed until the pro-
gramme number is displayed.
5) For music control of the colour change programmes
Sh 1 – Sh12 (the other programmes cannot be music-
controlled), the music control must be switched on:
a) Press button MENU so many times until
displayed.
b) Activate menu item
The display shows the operating state:
= music control switched on
= music control switched off:
The programme
adjusted speed.
c) Use button DOWN or UP to switch the music
control on or off and confirm with button ENTER.
The display returns to the indication
15 seconds the selected programme starts and
the display shows again the number of the pro-
gramme. For a quicker start of the programme
keep button MENU pressed until the display
shows the number of the programme.
If the music is played with a clear rhythm in the bass
range at sufficient volume and the music control is
switched on, the selected programme is controlled via
the microphone (7). With each music control pulse the
green LED SOUND (6) shortly lights up. If the music
control should not function in an optimum way,
increase the volume or reduce the distance between
the sound source and the PARL-7DMX.

6.1.2 Colour spotlight

The unit is capable of radiating one of 16 preset
colours at maximum brightness or a manually adjusted
colour at any desired brightness.
A. Selecting a preset colour
1) Press button MENU (5) so many times until
displayed.
2) Activate the menu item with button ENTER. The
display shows the colour last adjusted (
or ).
3) Select a colour with button DOWN or UP (1 = red ...
16 = white,
next paragraph) and confirm with button
ENTER. The display returns to
onds it shows the selected colour number and the
spotlight radiates the corresponding colour.
B. Manual colour adjustment
Hint: When adjusting the primary colours, not only their
brightness changes but also the shade of colour in case the
colours are mixed. Therefore, first adjust the colour which is
to dominate to the desired brightness and then add the other
two colours. If the intended colour mixture is white, first
adjust the brightness of the green colour because this
appears to be the brightest colour to the human eye. Then
add red to get yellow and finally add blue to get white.
with button ENTER.
operates with
= manual colour adjustment,
. After 15 sec-
1) Press button MENU (5) so many times until the dis-
play shows
2) Activate the menu item with button ENTER. The
display shows the colour last adjusted (
or
3) Use button DOWN or UP to switch to
ual). Activate the function with button ENTER. The
display now shows
is
4) Use button DOWN or UP to switch to
colour green and to
again to
adjusted first.
5) Press button ENTER so that the value of the
selected colour is displayed (indication 0 – 255).
Adjust the brightness of the colour with button
the
DOWN or UP and confirm with button ENTER.
6) Repeat the steps 4 and 5 for the further colours so
that the desired shade of colour with the desired
. After brightness will result.
7) For fine adjustment of the shade of colour, a colour
can be selected again with button DOWN or UP,
and after pressing button ENTER, it can be read-
justed with the buttons DOWN and UP. Then press
button ENTER again.
8) If no button is actuated within 15 seconds, the dis-
play returns to the indication
shade of colour, restart with step 1, if required.

6.2 Interconnecting several PARL-7DMX units

Several PARL-7DMX units may be interconnected.
Then all slave units can be controlled in sync with the
master unit.
1) Connect the DMX OUTPUT (9) of the master unit
via a 3-pole XLR cable (e. g. series MEC-... or
MECN-... from the product range of "img Stage
Line") to the DMX INPUT (10) of the first slave unit.
2) Connect the DMX OUTPUT of the first slave unit to
is
the DMX INPUT of the second slave unit, etc. until
all units have been connected in a chain.
3) Adjust the master mode at the master unit.
...
a) Press button MENU (5) so many times until the
indication
b) Press button ENTER. The display now shows
the adjusted mode (
c) Adjust
4) Adjust the type of control at the slave units.
a) Press button MENU (5) so many times until the
indication
b) Press button ENTER. The display now shows
the adjusted mode (
c) Adjust the desired mode with button UP or
DOWN:
= The slave unit is controlled in sync by
.
) in a flashing way.
(red).
for blue and then back
for red. Select the colour to be
is shown on the display (3).
...
with button UP or DOWN.
is shown on the display (3).
...
the master unit.
GB
...
(man-
for the
. To change the
or ).
or ).
15