Colour Radiator; Interconnecting Several Parl-4Set Units - IMG STAGELINE PARL-4SET Mode D'emploi

3) Select one of the programmes 0 – 12 with button
DOWN or UP or select the indication
the colour transition programme. Confirm the selec-
tion with button ENTER. The display will switch to
the indication of the running speed (
Note: For programme No. 0 no running speed can be
selected because it is only controlled by music. After
pressing the button ENTER, the display stops blinking.
Once the internal microphone picks up sound, the pro-
gramme starts after 60 seconds.
4) Use button DOWN or UP within 60 seconds to ad-
just the desired running speed. The unit will switch to
this speed when no music control exists [with the
music control switched off (
vals, or when the volume is too low]. Confirm the
adjustment with button ENTER. The display returns
to the indication of the programme number (flashing).
After one minute the flashing stops and the
selected programme starts. The yellow LED MAS-
TER (8) lights up. For a quicker start of the pro-
gramme keep the button MENU pressed until the
display stops flashing.
Note: When programme No. 0 is not music-controlled
(step 5), the colour transition function will be activated.
5) For music control of programmes 0 – 12 (pro-
gramme cannot be music-controlled), the
music control must be switched on:
a) Press button MENU so many times until
displayed.
b) Activate menu item
The display shows the operating state:
= music control switched on
= music control switched off:
The programme operates with the ad-
justed speed.
c) Use button DOWN or UP to switch the music
control on or off and confirm with button ENTER.
The display returns to
the selected programme starts and the display
shows again the number of the programme. For
a quicker start of the programme keep the button
MENU pressed until the display shows the num-
ber of the programme.
If the music is played with a clear rhythm in the bass
range at sufficient volume, the selected programme is
controlled via the microphone (7). With each music
control pulse the green LED SOUND (12) shortly lights
up. If the music control should not function in an opti-
mum way, increase the volume or reduce the distance
between the sound source and the PARL-4SET.

6.1.2 Colour radiator

The unit is capable of radiating one of 9 preset colours
at maximum brightness or a manually adjusted colour
at any desired brightness.
A Selecting a preset colour
1) Press button MENU (13) so many times until
is displayed.
(fade) for
...
step 5), in music inter-
with button ENTER.
. After 60 seconds
2) Activate the menu item with button ENTER. The
display shows the colour last adjusted (
or ) in a flashing way.
3) Select a colour with button DOWN or UP [1 = red ...
).
9 = white,
paragraph] and confirm with button ENTER. The dis-
play stops blinking.
B Manual colour adjustment
Hint: When adjusting the brightness of the red, green, or
blue LEDs, not only their brightness will be modified but in
case of a combination of these colours, the shade of colour
will also be modified. Therefore, first adjust the colour which
is intended to dominate to the desired brightness, and then
add the other two colours. For the combination white, first
adjust the brightness of the colour green, because this colour
appears to the eye to be the brightest colour. Then add red
to result in yellow and finally add blue to result in white.
1) Press button MENU (13) so many times until the
display shows
2) Activate the menu item with button ENTER. The
display shows the colour last adjusted (
or ) in a flashing way.
3) Use button DOWN or UP to switch to
ual). Activate the function with button ENTER. The
display now shows
the red LEDs.
4) Use button ENTER to switch to for the colour green
is
and to for blue and then back again to for red.
5) Adjust the selected colour with button DOWN or UP
(indication 0 – 255) so that the desired shade of
colour with the desired brightness will result.
6) For fine adjustment of the shade of colour a colour
can be selected again with button ENTER and be
readjusted with the buttons DOWN and UP.
7) If no button is actuated within 60 seconds, the unit
returns to the indication
of colour, start again with step 1, if required.

6.2 Interconnecting several PARL-4SET units

Several PARL-4SET units may be interconnected.
Then all slave units can be controlled in sync with the
master unit.
1) Connect the DMX OUTPUT (5) of the master unit
via a 3-pole XLR cable (e. g. series MEC-... or
MECN-... from the product range of "img Stage
Line") to the DMX INPUT (4) of the first slave unit.
2) Connect the DMX OUTPUT of the first slave unit to
the DMX INPUT of the second slave unit, etc. until
all units have been connected in a chain.
No DMX signal must be present at the DMX INPUT of
the master unit, so that the yellow LED MASTER (8)
lights up and the unit is thus switched to the master
mode. Once the control signals from the master unit
are applied to the slave units, the red LED SLAVE (11)
will light up on the slave units. The slave units are then
automatically switched to the slave mode and can be
controlled in sync with the master unit.
= manual colour adjustment,
.
and the brightness value for
. To change the shade
GB
...
next
...
(man-
15