Briggs & Stratton 120000 Manuel D'utilisation page 10

Fuel Filter, if equipped
1. Before cleaning or replacing the fuel filter (A, Figure 18), drain the fuel tank or close
the fuel shut-off valve. Otherwise, fuel can leak out and cause a fire or explosion.
2. Use pliers to squeeze tabs (B, Figure 18) on the clamps (C), then slide the clamps
away from the fuel filter (A). Twist and pull the fuel lines (D) off of the fuel filter.
3. Check the fuel lines (D, Figure 18) for cracks or leaks. Replace if necessary.
4. Replace the fuel filter (A, Figure 18) with an original equipment replacement filter.
5. Secure the fuel lines (D, Figure 18) with clamps (C) as shown.
Fuel Strainer, if equipped
1. Remove the fuel cap (A, Figure 19).
2. Remove the fuel strainer (B, Figure 19).
3. If the fuel strainer is dirty, clean or replace it. If you replace the fuel strainer, make
sure to use an original equipment replacement fuel strainer.
Service Cooling System
WARNING
Running engines produce heat. Engine parts, especially muffler, become extremely
hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc., can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
NOTICE Do not use water to clean the engine. Water could contaminate the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to
overheat, resulting in poor performance and reduced engine life.
1. Use a brush or dry cloth to remove debris from the air intake grille.
2. Keep linkage, springs and controls clean.
3. Keep the area around and behind the muffler, if equipped, free of any combustible
debris.
4. Make sure the oil cooler fins, if equipped, are free of dirt and debris.
After a period of time, debris can accumulate in the cylinder cooling fins and cause the
engine to overheat. This debris cannot be removed without partial disassembly of the
engine. Have a Briggs & Stratton Authorized Service Dealer inspect and clean the air
cooling system as recommended in the Maintenance Schedule.
Storage
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Storing Fuel Or Equipment With Fuel In Tank
• Store away from furnaces, stoves, water heaters or other appliances that have pilot
lights or other ignition sources because they can ignite fuel vapors.
Fuel System
See Figure: 20
Store the engine level (normal operating position). Fill fuel tank (A, Figure 20) with fuel.
To allow for expansion of fuel, do not overfill above the fuel tank neck (B).
Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum deposits
to form in the fuel system or on essential carburetor parts. To keep fuel fresh, use Briggs
& Stratton Advanced Formula Fuel Treatment & Stabilizer, available wherever Briggs
& Stratton genuine service parts are sold.
There is no need to drain gasoline from the engine if a fuel stabilizer is added according
to instructions. Run the engine for two (2) minutes to circulate the stabilizer throughout the
fuel system before storage.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into
an approved container. Run the engine until it stops from lack of fuel. The use of a fuel
stabilizer in the storage container is recommended to maintain freshness.
10
Engine Oil
While the engine is still warm, change the engine oil. See the Change Engine Oil section.
Troubleshooting
For assistance, contact your local dealer or go to BRIGGSandSTRATTON.com or call
1-800-233-3723 (in USA).
Specifications
Model: 120000
Displacement
Bore
Stroke
Oil Capacity
Gear Reduction Oil Type
Gear Reduction Oil Capacity
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
Model: 150000
Displacement
Bore
Stroke
Oil Capacity
Gear Reduction Oil Type
Gear Reduction Oil Capacity
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
Model: 200000
Displacement
Bore
Stroke
Oil Capacity
Gear Reduction Oil Type
Gear Reduction Oil Capacity
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
Model: 210000
Displacement
Bore
Stroke
Oil Capacity
Gear Reduction Oil Type
Gear Reduction Oil Capacity
Spark Plug Gap
12.48 ci (205 cc)
2.688 in (65,28 mm)
2.200 in (55,88 mm)
18 - 20 oz (,54 - ,59 L)
80W-90
4 oz (0,12 L)
.030 in (,76 mm)
180 lb-in (20 Nm)
.010 - .014 in (,25 - ,36 mm)
.004 - .006 in (,10 - ,15 mm)
.009 - .011 in (,23 - ,28 mm)
15.24 ci (250 cc)
2.970 in (75,44 mm)
2.200 in (55,88 mm)
18 - 20 oz (,54 - ,59 L)
80W-90
4 oz (0,12 L)
.030 in (,76 mm)
180 lb-in (20 Nm)
.010 - .014 in (,25 - ,36 mm)
.004 - .006 in (,10 - ,15 mm)
.009 - .011 in (,23 - ,28 mm)
15.63 ci (305 cc)
3.120 in (79,24 mm)
2.438 in (61,93 mm)
26 - 28 oz (,77 - ,83 L)
SAE 30
12 oz (,35 L)
.030 in (,76 mm)
180 lb-in (20 Nm)
.008 - .012 in (,20 - ,30 mm)
.004 - .006 in (,10 - ,15 mm)
.004 - .006 in (,10 - ,15 mm)
20.85 ci (342 cc)
3.300 in (83,81 mm)
2.438 in (61,93 mm)
26 - 28 oz (,77 - ,83 L)
SAE 30
12 oz (,35 L)
.030 in (,76 mm)
BRIGGSandSTRATTON.com