CAME G4040Z Manuel D'installation page 26

• This product should only be used for the purpose for which it was explicitly
designed. Any other use is dangerous. CAME S.p.A. is not liable for any damage
caused by improper, wrongful and unreasonable use • The safety of this
product and its proper fi tting depends, therefore, on respecting its technical
characteristics and proper fi tting, to be done in state-of-the-art fashion, and
under safe conditions as expressly explained in the technical literature that
comes with the product.• Keep these warnings together with the installation
and operation manuals that come with the operator.
Before installing
(checking what's there: if something is missing, do not continue until you
have complied with all safety provisions)
• Fitting and testing must be be only performed by qualifi ed technicians
• Laying the cables, installation and testing must follow state-of-the-art
procedures as dictated by regulations • Before beginning any operation
it is mandatory to carefully read all instructions; improper installation may
result in serious harm to people and things • Make sure the boom is in good
mechanical state, balanced and aligned, and that it opens and closes properly.
Also, if needed, fi t suitable protections or use proper safety sensors. If the
operator is to be installed at a height of under 2.5 m from the ground or other
access level, make sure you have any necessary protections and/or warnings
in place • Make sure that the opening of the automatic barrier does not create
a danger. • Do not install the operator upside down or onto elements that could
yield and bend. If necessary, add suitable reinforcements to the anchoring
points • Do not install on tilted surfaces • Make sure the temperature range
shown on the product literature is suitable for the climate where it will be
installed as explained in the manual Check that any irrigation devices will not
wet the operator from the bottom upwards.
• Suitably section off and demarcate the entire installation site to prevent
unauthorized persons from entering the area, especially minors and children
• Be careful when handling operators that weigh over 20 kg. If need be, use
proper safety hoisting equipment • The CE-marked safety devices (photocells,
stepping plates, sensitive safety-edges, emergency buttons, and so on), must
be fi tted in compliance with the regulations in eff ect and according to state-
of-the-art criteria, taking into account the environment, the type of required
service and the working forces applied to moving leaves. Any shearing or
conveying points must be sensor-protected • Any residual risks must be
pointed out to end users and highlighted with pictograms as provided by law.
• All opening commands (that is, buttons, key switches, magnetic readers,
and so on) must be installed at least 1.85 m from the perimeter of the barrier's
working area, or where they cannot be reached from outside the barrier. Also,
any direct commands (buttons, touch panels, and so on) must be installed
at least 1.5 m from the ground and must not be reachable by unauthorized
persons • The automatic barrier must visibly show its identifi cation data. •
Before connecting the mains power supply make sure that the identifi cation
data correspond to the those of the network • The automatic barrier must be
connected to an eff ective regulation grounding system.
• The manufacturer declines any liability for using non-original products;
which would result in warranty loss • All maintained action commands must
be fi tted in places from which the moving barrier and transit and driving areas
are visible • Apply, if missing, a permanent sign showing the position of the
release device • Before delivering to the users, make sure the system is EN
12453 and EN 12445 standard compliant (regarding impact forces), and
also make sure the system has been properly adjusted and that any safety,
protection and manual release devices are working properly • Apply Warning
Signs where necessary and in a visible place (such as the gate's license plate)
Special user-instructions and recommendations
• Keep barrier operation areas clean and free of any obstructions. Make sure
the photocell's operating fi eld is clear of any obstructions • Do not allow
children to play with fi xed commands, or to loiter in the barrier's maneuvering
area. Keep any remote control transmitters or any other command device
away from children, to prevent the operator from being accidentally activated
• The apparatus may be used by children of eight years and above and by
physically, mentally and perceptively challenged people, or even ones without
any experience, provided this happens under close supervision or once they
have been properly instructed to use the apparatus safely and to the potential
hazards involved • Children must not play with the apparatus. Cleaning and
maintenance by users must not be done by children, unless properly supervised
• Frequently check the system for any malfunctions or signs of wear and tear
or damage to the moving structures, to the component parts, all anchoring
important safety instructions for people:
READ CAREFULLY!
Premise
Installing
WARNING!
points, including cables and any accessible connections • Keep any hinges,
moving joints and slide rails properly lubricated. Perform functional checks
on the photocells and sensitive safety edges, every six months. Constantly
clean the photocells' glass covers using a slightly water-moistened cloth; do
not use solvents or chemicals that could damage the devices • If repairs or
modifi cations are required to the system, release the operator and do not use
it until safety conditions have been restored • Cut off the power supply before
releasing the operator for manual openings and before any other operation,
to prevent potentially hazardous situations. Read the instructions • If the
power supply cable is damaged, it must be replaced by the manufacturer or
authorized technical assistance service, or in any case, by similarly qualifi ed
persons, to prevent any risk • It is FORBIDDEN for users to perform any
OPERATIONS THAT ARE NOT EXPRESSLY REQUIRED OF THEM AND WHICH ARE
NOT LISTED in the manuals. For any repairs, modifi cations and adjustments
and for extra-ordinary maintenance, CALL TECHNICAL ASSISTANCE • Log the
job and checks in the periodic maintenance log.
Further recommendations for all
• Keep away from and do not loiter near the barrier and mechanical moving
parts • Do not enter the barrier's area of operation when it is moving • Do not
counter the operator's movement as this could result in dangerous situations
• Always pay special attention to any dangerous points, which have to be
labeled with specifi c pictograms and/or black and yellow stripes • When using
a selector switch or a command in maintained action, keep checking that
there are no persons within the operating range of any moving parts, until the
command is released • The barrier may move at any time and without warning
• Always cut off the power supply before performing any maintenance or
cleaning.
Danger of hand crushing
Danger! High voltage.
No transiting while the barrier is moving