110
EGO / EGO PRIME
2.136
EGO - external dimensions (L x P x H)
711
217
2.055
EGO PRIME -
620
external dimensions (L x P x H)
213
Inclination height 45°(h)
620
Size of the bracket pitch (B)
2050
EGO gross surface area
1,52 m
2
EGO PRIME -gross surface area
1,28 m
2
surface area when open
1,09 m
2
absorption surface area
0,85 m
2
effective ACS content
105 litri
cover requirements
1-2
EGO - net weight (empty)
36 kg
EGO PRIME - net weight (empty)
29 kg
EGO - working weight (full)
141 kg
EGO PRIME - working weight (full)
134 kg
maximum working pressure
maximum working temperature
heat-transfer fluid
hydraulic connections
thickness and heat insulation type
30 in PUR (fondo) - 25 in poliestere (laterale) [mm]
installation
degree of slope
bleed recommended at 45 °C
L
B
Rev. 4.0 del 16|03|2022
Technical data
150
180
220
2.136
2.136
2.136
2.136
906
1,101
1.296
1.491
217
217
217
2.055
2.055
2.055
2.055
815
1,010
1.205
1.400
213
213
213
760
895
1035
1170
2050
2050
2050
2050
1,93 m
2,35 m
2,77 m
3,18 m
2
2
2
1,68 m
2,08 m
2,48 m
3,88 m
2
2
2
1,48 m
2
1,86 m
2
2,25 m
2
2,64 m
1,13 m
1,41 m
1,69 m
1,98 m
2
2
2
140 litri
175 litri
210 litri
245 litri
2-3
3-4
4-5
43 kg
50 kg
57 kg
65 kg
36 kg
43 kg
50 kg
58 kg
183 kg
225 kg
267 kg
310 kg
176 kg
218 kg
260 kg
302 kg
400 kPa
90 °C
ACS
2 x ¾'' M
tetto piano - tetto inclinato
45° (tetto piano) - 15-60° (tetto inclinato)
-
H
P
45°
34
Warnings
General indications
y This document is an integral and essential part of the product. It
is to be used by the installer and the end user, who must keep it
260
carefully after the system has been installed and started.
y The manufacturer is not liable for any damage deriving from
incorrect observation of the instructions and indications given in
this document, those relative to possible accessories supplied with
217
the system and for the non-observance of pertinent applicable
national and local laws.
y Before installation and use, obtain information on the current
regulations and laws in the place where the system is to be
213
installed.
y The solar collector with integrated storage was designed and
manufactured to produce domestic water that is heated by solar
power. Any use other than that indicated relieves the manufacturer
from any responsibility and renders all guarantees null and void.
2
y All technical drawings, plant layout and electric wiring diagrams
2
etc. that are present in this manual are indicative and are only given
2
as examples. All connections, the safety devices, diameter sizes and
any other thing necessary for correct system installation must be
2
verified by a qualified and expert technician, who must make sure
of their correspondence with regulations and laws in force.
y The manufacturer is not liable for any damage caused to the
5-6
product resulting from assembly that is not state-of-the-art.
Indications for safety
y This product must be installed by a professionally qualified
company or technician, according to national and/or local laws in
force and the instructions given in this handbook.
y Maintenance and cleaning must also be carried out by specialist
companies or staff with the pertinent technical qualifications.
y The term 'professionally qualified technician' indicates a person
with specific technical skills in water for domestic use, as well as in
heating systems, gas systems and electric systems. This person must
have the professional skills indicated by law.
y On the basis of the user guidelines, whoever uses the system must
keep it in good condition and guarantee that it works safely and
correctly.
y The system user must ensure that the maintenance indicated in
this handbook (see the PROGRAMMED MAINTENANCE chapter)
is carried out.
y Do not leave parts of the packaging or the system within the reach
of children.
y Before cleaning or carrying out maintenance, disconnect the power
supply from any electric accessories that may be present.
h
y Dispose of the various packaging elements in a suitable manner.
y Check the pressure of the water transportation network: if the
pressure is higher than the nominal pressure of the product (4
bar = 400 kPa), prepare the necessary reduction units before the
connection and regulate the pressure (see STARTING chapter)
y Should faults occur, or if the system does not operate correctly, do
not attempt to repair the product. Instead, disable it and contact a
specialist technician. Should it be necessary, components must only
be replaced with original spare parts, which must be installed by
qualified technicians. Should this not be the case, the manufacturer
reserves the right not to recognise any guarantee rights.
Protection from vacuum overheating
The solar collector with integrated storage is supplied equipped with a
PVC cover sheet which darkens the surface that collects the sun's rays,
therefore protecting the product against overheating caused by direct
exposure, above all in the case when the collector has been installed
but is not connected to the water system (therefore no water present).
The collector, in fact, was not designed to be exposed directly to the
sun's rays without being filled with water.
Exposure to the sun when the system is empty
can damage the product; in this case the
manufacturer will not recognise any guarantee
rights.
The cover sheet must be left on the solar collector until it is started (see
also the STARTING chapter). Should it be necessary to empty the system
for maintenance or as a no-freeze function, it should be covered by the
cover sheet. If the maximum permissible temperature is exceeded due
to operation without water, this will be detected by a special detector
inside the panel, which will invalidate the warranty.
Protection from burns
Danger! The water inside the collector can reach temperatures of
approximately 90 °C. To prevent the danger of burns and/or scalds, be
extremely careful when:
- connecting the hydraulic supply to the domestic water supply;
- loading and unloading the system;
- carrying out any intervention on the hydraulic connection.
35