R&G CP0339BL Instructions De Montage page 18


Du coté droit de la moto, remonter le carénage supérieur (sans oublier de reconnecter les fils
de clignotants) et installer la protection crash restante.

Pour cela, glisser une rondelle M12 sur le boulon M12 x 70mm (Article 9) de façon à ce que la
rondelle se place contre la tête du boulon.

Glisser l'une des rondelles de blocage crantées autour du boulon de façon à ce qu'elle se
mette contre la rondelle tout juste installée.

Ensuite, glisser le boulon et les rondelles à travers la protection (Article 2 – B0431 avec
CS340) de sorte à ce que la tête du boulon aille en contre alésage dans la protection crash
puis poser l'ensemble sur le patron fileté sur le bloc de montage comme sur la photo.

Serrer les 2 protections crash jusqu'à ce que vous sentiez une légère compression de
l'intérieur de la protection, avec une clé de 19mm. LA PROTECTION DOIT ETRE POSITIONNEE
COMME EN PHOTO C AVEC LE COTE ARRONDI LE PLUS GROS EN DIRECTION DE L'AVANT DE
LA MOTO. Tourner un peu plus afin d'accentuer légèrement la compression. Ne pas trop
serer, au risqué d'abîmer la moto. Pas plus de 40 Nm.

Placer le logo en caoutchouc dans le creux de la protection.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not
refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 27/03/2013 (AR)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com Email: info@rg-racing.com