Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. CP0357BL
  6. Instructions

R&G CP0357BL Instructions

Masquer les pouces

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Télécharger ce manuel
FITTING INSTRUCTIONS FOR CP0357BL
AERO CRASH PROTECTORS
YAMAHA MT-09 '13-
Picture A
Picture B
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike
T
(
)
HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY
FOR CLARITY OF INSTRUCTIONS ONLY
8
7
9
6
10
5
5
4
3
3
11
2
12
LEFT
1
13
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

loading

Manuels Connexes pour R&G CP0357BL

Sommaire des Matières pour R&G CP0357BL

  • Page 1 FITTING INSTRUCTIONS FOR CP0357BL AERO CRASH PROTECTORS YAMAHA MT-09 ’13- Picture A Picture B THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Please note that the way the kit is packed does not necessarily represent the way of...
  • Page 2 RIGHT LEGEND ITEM 1 = CRASH PROTECTOR CAPS (BC0002) (x2). ITEM 2 = CRASH PROTECTOR (B0061 with CS340) (x2). ITEM 3 = M5x0.8x6mm LONG COUNTERSUNK BOLTS (x4). ITEM 4 = SMW0036 METAL INSERT LEFT (x1). ITEM 5 = M10 WASHERS (x4). ITEM 6 = M10x1.25x60mm LONG CAP HEAD BOLTS (x2).

  • Page 3: Tools Required

    TOOLS REQUIRED  Socket set to include 8mm A/F & 19mm socket and wrench.  3mm A/F Allen key.  Torque wrench (up to 40Nm). TOWARDS REAR TOWARDS FRONT OF BIKE OF BIKE PICTURE C Picture 1 Picture 2 Picture 3 Picture 4 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ...
  • Page 4 Picture 5 Picture 6 Picture 7 Picture 8 Picture 9 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...

  • Page 5: Fitting Instructions

    FITTING INSTRUCTIONS Left Side (as you sit on the bike)  Take the left side mounting block (item 8 – M0378) and assemble it as detailed below and shown in picture 1.  Fit one M10 washer (item 5) onto one of the M10 x 1.25 x 60mm long cap head bolts (item 6) and position through the front mounting hole of the metal block (boss machined into rear) ensuring that the head of the bolt and washer sit inside the recess.
  • Page 6  Ensure this is mounted correctly before tightening the two bolts to the manufacturers recommended torque settings. Do not over tighten as damage can occur to the bike.  Now fit the right side metal insert (item 17 – SMW0037) into the recess on the mounting block, before fitting the remaining two M5 x 6mm long countersunk bolts (item 3) and tighten, as shown in picture 8.
  • Page 7 INSTRUCTIONS DE MONTAGE POUR CP0357BL PROTECTIONS CRASH YAMAHA MT-09 ’13- Photo A Photo B E KIT CONTIENT LES ARTICLES EXPOSES CI DESSOUS VERIFIER QUE TOUTES LES PIECES SOIENT PRESENTES AVANT DE PROCEDER AU MONTAGE A FAÇON DONT LE KIT EST EMBALLE NE CORRESPOND PAS FORCEMENT A LA FAÇON DE MONTER LES PIECES...
  • Page 8 DROIT LEGENDE ARTICLE 1 = Capuchons de protection crash (BC0002) (x2). ARTICLE 2 = Protection crash (B0061 avec CS340) (x2). ARTICLE 3 = M5x0.8x6mm Boulons (x4). ARTICLE 4 = SMW0036 Insert en métal coté gauche (x1). ARTICLE 5 = M10 Rondelles (x4). ARTICLE 6 = M10x1.25x60mm Boulons (x2).
  • Page 9 Outils requis :  Jeu de clés 8mm et 19mm  Clé Allen 3mm.  Clé dynamométrique (à 40 Nm). ARRIÈRE MOTO AVANT MOTO PHOTO C Photo 1 Photo 2 Photo 3 Photo 4 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email:...
  • Page 10 Photo 5 Photo 6 Photo 7 Photo 8 Photo 9 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 11 INSTRUCTIONS DE MONTAGE : Coté gauche (assis sur la moto) :  Prendre le bloc de montage coté gauche (Article 8 – M0378) et assemblez le comme détaillé ci dessous (Photo 1).  Glisser une rondelle M10 (Article 5) sur un des boulons M10 x 1.25 x 60mm (Article 6) et positionnez le à...
  • Page 12  Prendre le boulon M10 x 1.25 x 100mm (Article 14) et glissez-y la rondelle M10 restante (Article 5). Positionnez-le à travers le trou de fixation arrière (surface plate à l’arrière) en veillant à ce que la tête du boulon et la rondelle se placent dans le creux. ...