1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. CP0331BL
  6. Manuel d'instructions

R&G CP0331BL Manuel D'instructions

Masquer les pouces
1
2
3
4
5
6
7
8
9
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Télécharger ce manuel
FITTING INSTRUCTIONS FOR CP0331BL AERO CRASH PROTECTORS
SUZUKI INAZUMA 250 2012
Page | 1
PICTURE 'A'
PICTURE 'B'
REAR OF BIKE
FRONT OF BIKE
PICTURE 'C'
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike
Please note that in cases where kits are packed with rubber washers holding the components
onto the bolt – the rubber washers should be thrown away!
T
(
)
HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY
FOR CLARITY OF INSTRUCTIONS ONLY
R&G Racing
Unit 1 Shelleys Lane, East Worldham, Alton, Hants GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

Table des Matières
loading

Manuels Connexes pour R&G CP0331BL

Sommaire des Matières pour R&G CP0331BL

  • Page 1 FITTING INSTRUCTIONS FOR CP0331BL AERO CRASH PROTECTORS SUZUKI INAZUMA 250 2012 Page | 1 PICTURE ‘A’ PICTURE ‘B’ REAR OF BIKE FRONT OF BIKE PICTURE ‘C’ THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.

  • Page 2: Left Hand Side

    Page | 2 LEFT HAND SIDE RIGHT HAND SIDE TOOLS REQUIRED  Socket set to include 8, 2x14 and 2x17mm socket and wrench.  Set of Allen keys set to include 4mm A/F.  Torque wrench (up to 40Nm). R&G Racing Unit 1 Shelleys Lane, East Worldham, Alton, Hants GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
  • Page 3 LEGEND ITEM 1 = M10 NYLOC NUTS (x2). Page | 3 ITEM 2 = M10 PLAIN WASHERS (x2). ITEM 3 = LW0001 (M12 SHAKE PROOF WASHERS) (x2). ITEM 4 = B0061 with CS341 (10mm) (BOTH CRASH PROTECTORS) (x2). ITEM 5 = EB070 ENGINE BAR (440mm LONG) (x1). ITEM 6 = S0601 L-H-S SPACER (138mm LONG) (x1).

  • Page 4: Fitting Instructions

    FITTING INSTRUCTIONS Near side (left side as you sit on bike)  Remove the two bolts arrowed in picture 1. Page | 4  Remove the nut in position arrowed in picture 2.  Use the new engine bar (item 5) to push the original bolt out leave the same amounts protruding from either side.
  • Page 5 The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes.
  • Page 6 Instructions de montage pour CP0331BL Protections crash latérales SUZUKI INAZUMA 250 2012 Page | 6 PHOTO ‘A’ PHOTO ‘B’ REAR OF BIKE FRONT OF BIKE PHOTO ‘C’ E KIT CONTIENT LES ARTICLES EXPOSES CI DESSOUS VERIFIER QUE TOUTES LES PIECES SOIENT PRESENTES AVANT DE PROCEDER AU MONTAGE La façon dont le kit est emballé...

  • Page 7: Coté Droit

    Page | 7 Coté gauche Coté droit Outils requis  Clés à molette 8, 2x14 et 2x17mm  Clé Allen 4mm  Clé dynamométrique (à 40Nm). R&G Racing Unit 1 Shelleys Lane, East Worldham, Alton, Hants GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 8 LEGENDE ARTICLE 1 = M10 ECROUS EN NYLOC (x2). ARTICLE 2 = M10 RONDELLES PLATES (x2). Page | 8 ARTICLE 3 = LW0001 (M12 RONDELLES SHAKE PROOF) (x2). ARTICLE 4 = B0061 avec CS341 (10mm) (LES 2 PROTECTIONS) (x2). ARTICLE 5 = EB070 AXE MOTEUR (440mm de long) (x1). ARTICLE 6 = S0601 ENTRETOISE COTE GAUCHE (138mm de long) (x1).
  • Page 9 Instructions de montage Coté gauche (assis sur la moto)  Enlever les 2 boulons (Photo 1).. Page | 9  Enlever l’écrou en position (Photo 2).  Utiliser le nouvel axe moteur (Article 5) pour pousser le boulon d’origine vers l’extérieur, en laissant dépasser la même longueur de chaque coté.

Table des Matières