R&G LP0121 Instructions page 5


Within the rubber extension, there is a metal plate. This needs to be removed and is easiest with the
use of a screwdriver to pry it out, as shown in picture 7.

Now offer into place on the license plate bracket, ensuring the correct indicators go to the correct
side). Pass the cable through the hole and position the indicator against the metal. Now slide on
one of the original metal plates which have just been removed onto the cable. Using the original
bolt, tighten the assembly back together, as shown in picture 8.

If fitting mini indicators (we suggest R&G product code RG370) you will need to use the indicator
adaptors (item 9).

Attach the undertray to the license plate bracket using 4x M6x8mm button head bolts and washers,
as shown in picture 9. Ensure the wires for the indicators and license plate illuminator clear the
metalwork.

Now sit the tail tidy assembly on the rear wheel whilst you connect the remaining wires. At this
point, the cable for the rear lock also needs to be re-fitted to the locking mechanism. (It is a good
idea to test all lights work correctly at this stage).

Offer the tail tidy up to the underside of the bike, taking care to ensure no wires become trapped.
With it in place, screw in loosely the original 6mm allen key bolts, as shown in picture 10.

Ensure the rear seat lock operates correctly along and all the wires clear the metal work, before
tighten all 4 bolts evenly.

IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT FAR DOWN ON THE
LICENCE PLATE HANGER, THERE IS A SMALL CHANCE OF THE LICENCE PLATE HITTING THE
BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE ROAD. IT IS YOUR
RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING ACTION. FAILURE TO
CHECK THIS COULD RESULT IN SERIOUS INJURY.

Refit the seat unit and licence plate (it may require drilling).

Depending on local laws, attach enclosed reflector in an appropriate location.

Test the license plate illuminator and all lights before riding.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its
particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any
fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable
condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc.
P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued
products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
ISSUE 1 08/06/12 (AR)
Email: info@rg-racing.com