Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
INSTALLATION INSTRUCTIONS
2200SFK Steel Framing Kit
CSA approved for use with Valor models 2200 ONLY
Note: This kit must be installed by a qualifi ed installer. These instructions are to
be used in conjunction with the main installation instructions for the above listed
models.
Description of Kit
The 2200SFK—Steel Framing Kit consists of 3 sections:
Upper, Middle and Lower section designed to match
the footprint of LX2 appliances.
The upper and lower sections are supplied assembled.
The middle section is supplied knocked-down and
requires fi eld assembly (screws).
The upper section is designed to accommodate the 38-
inch forward-facing LDK4 plenum, the two side-facing
LDK3 plenums or the upward-facing LDK7 duct termi-
nation plates along with a required minimum 2-1/2"
ceiling gap discharge outlet.
The minimum total height using the steel framing kit
is approximately 91 inches—additional framing can be
added between the sections to accommodate various
ceiling heights or simply mount the framing sections
with gaps between them and span the gaps with the
wall fi nish material.
Note: Combustible materials are not allowed within the
framing kits below appliance stand-off height. Non-
combustible wall fi nish is required—refer to appliance
manual for limits.
Notes
• This kit will need to install before venting .
• Rough-in gas and electrical before installing this kit.
• Extra framing may be required to anchor this
framing kit to the wall.
• Drywall/insulation may need to be installed behind
the appliance location before this kit is installed.
Plan accordingly!
• Do not let the weight of heavy wall fi nishes bear on
top of appliance—leave gap between appliance and
middle section of this kit.
4006266-03
© 2020, Miles Industries Ltd. All rights reserved.
LX2 Series
Kit Overview
11-5/8"
35-3/8"
32-1/2"
*10-1/4"
*3/4" high
feet nest
inside lower
section
11-5/8"
52"
Minimum Total Height: 91-1/8" (approx.)
Upper Section
(supplied assembled)
Houses HeatShift
plenum/plates
Middle Section
(supplied knocked
down)
Remote Batteries &
Wall Switch Control
20"
LX2 Fireplace
Remove handles
Lower Section
(supplied assembled)
18"
Note: Appliance
extends 20" out
from the wall
1
Publicité
Table des Matières
Manuels Connexes pour Valor 2200SFK
Sommaire des Matières pour Valor 2200SFK
- Page 1 LX2 Series 2200SFK Steel Framing Kit CSA approved for use with Valor models 2200 ONLY Note: This kit must be installed by a qualifi ed installer. These instructions are to be used in conjunction with the main installation instructions for the above listed models.
-
Page 2: Installation Overview
Installation Overview Installation Sequence 9. Install upper section 10. Install and connect venting to appliance 1. Prepare wall behind appliance, including additional framing for vent outlet 11. Install and connect HeatShift fl ex pipes to appliance and plenum/plates 2. Rough-in gas and electrical 12. -
Page 3: Wall Preparation
Wall Preparation Plan venting and prepare vent penetration through wall before installing this kit Unswitched power supply for standard overhead lighting. Leave plenty of wire (36”) for connection Note - May require to appliance. drywall/insulation Note: If using the installed behind optional 2200ULK 10”... - Page 4 Installation Base Section (optional) 1. Place base section in position with the 2” stand-off s against the rear wall. 2. Place LX2 appliance on top of base section keeping a 2” clearance from the rear wall. 3. Fold down fi xing tabs at the base of the appliance and screw to the base.
- Page 5 b) Assemble the two side panels to the bottom d) Assemble the two front vertical studs to the frame (9 screws per side). The side panels front of the section. are identical. The cutout in each panel is a Note: The studs may be installed potential location for the Remote Battery &...
- Page 6 5. Place the assembled middle section above the appliance. Use shims to provide a gap between the framing kit and the appliance to ensure weight of wall is not transferred to the appliance top. a) Fix the framing kit to the wall using 3-1/4” b) Use additional screws through lower sheet screws through the nested 2 x 4 into a metal frame into studs to secure bottom of...
- Page 7 Top Section b) Install the chosen plenum(s) and screw into place. The top section is designed to accommodate the HeatShift outlet. Please note that LDK1—48” plenum cannot be installed with this framing kit. To make the installation easier, we recommend fi tting the plenum or duct termination plates to the top section before installing the section.
- Page 8 9. Install the top section on top of or above the middle section. To accommodate various ceiling heights, either fasten upper section to ceiling and have the wall finish span the gap between the upper and middle sections OR add framing/shims between the upper and middle sections - added framing/shims can be wood or steel.
- Page 9 Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication. Designed and Manufactured by / for Miles Industries Ltd. 190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1 Tel. 604-984-3496 Fax 604-984-0246 www.valorfi replaces.com...
-
Page 10: Trousse D'encastrement En Acier 2200Sfk
Description de la trousse Concept La Trousse d’encastrement en acier 2200SFK est compo- sée de 3 sections : les sections du haut, du milieu et du 11-5/8” bas, dont l’empiètement est le même que les foyers LX2. -
Page 11: Aperçu De L'installation
Aperçu de l’installation Séquence d’installation 8. Installez le(s) plénum(s) ou plaques HeatShift dans la section du haut 1. Préparez le mur derrière l’appareil, incluant 9. Installez la section du haut l’emplacement où sortira le conduit d’évent. 10. Installez le système d’évacuation 2. -
Page 12: Préparation Du Mur
Préparation du mur Planifiez l’évacuation et préparez le mur pour la pénétration du conduits d’évent avant l’installation de cet encastrement Alimentation électrique non commutée pour éclairage fourni. Laissez une bonne longueur de fil (36” - 0,9 m) pour Note - Il est possible le raccord à... - Page 13 Installation Section du bas (optionelle) 1. Placez la section du bas en position avec les écarteurs de 2 pouces contre le mur arrière. 2. Placez l’appareil LX2 sur la section du bas toujours en gardant un dégagement de 2 pouces vers le mur arrière.
- Page 14 b) Assemblez les deux panneaux des côtés au d) Assemblez les deux poutres verticales au cadre du bas (9 vis par côté). Les panneaux devant de la section. des côtés sont identiques. L’ouverture dans le Note : Ces poutres peuvent panneau peut être utilisée pour le Porte-piles être installées plus tard afin et interrupteur mural fourni avec l’appareil.
- Page 15 5. Placez la section du milieu assemblée au-dessus de l’appareil. Utilisez des cales pour créer un espace entre l’encastrement et l’appareil afi n de vous assurer que le poids du mur ne sera pas transféré au dessus de l’appareil. b) Fixez le bas de la section par son cadre aux a) Fixez la section du milieu à...
- Page 16 Section du haut Installez les plaques d’extrémité des con- LDK7. duits LDK7 en les fi xant directement à l’encadre- La section du haut est conçue pour contenir la sortie ment. Les profi lés en U ne sont pas requis pour ce du système de canalisation HeatShift.
- Page 17 10. Appliquez la fi nition du mur par-dessus l’encastrement et fi xez-la aux poutres de métal et à la caisse de l’appareil avec des vis auto-fi letées. Pour l’adapter à diverses hauteurs de plafonds, fixez la section du haut au plafond et couvrez l‘espace entre la section du haut et celle du milieu avec la finition du mur.
- Page 18 Liste de pièces Description Pièce n Profi lés en U pour LDK3 et LDK4 (2) 4006662 Section du haut 4006657 Section du milieu 4006658 Cadres haut/bas (2) 4006663 Panneaux des côtés (2) 4006664 Poutres d’acier avant (2) 4006665 Section du bas 4006659 Vis noires #8 x 1/2”...